TnB Color-Keyed Cable Stripper BCS8-40 소개자료

 

안녕하세요 TIATIP 입니다.

 

아직도 컷터칼로 불안하게 탈피작업을 하고 계십니까? 현장에서 작업을 하다보면 작업자가 다치거나, 케이블의 손상이 발생하는 경우가 간혹 있으며, 작업자의 숙련도에 따라 균일한 반복정도로 품질이 유지되기가 어려운 실상을 확인할 수 있습니다. 티앤비에서는 Non-Armoured Cable은 물론 Armoured Cable의 피폭을 벗길 때, 작업자의 사용편의성과 깔끔한 관리가 가능한 스트리퍼 BCS8-40 을 소개드립니다.

 

 

Thomas&Betts, TnB (T&B)

Color-Keyed Cable Stripper

CAT.NO. BCS8-40

Cable Stripper for 8 AWG-4/0 Battery cable with replacement blade provided in the handle

 

 

 

 

 


TnB Instructions for Cat. No. BCS8-40

WARNING : DO NOT PLACE FINGERS BETWEEN THE CABLE SUPPORT BRACKET AND THE BLADE.

 

 

A. AJUSTING BLADE
NOTE: A sharp blade is contained beneath the cable support
bracket of this tool. Upon raising the cable support bracket (as
in steps 1 and 2), the blade will be exposed. Care should be
used in inserting and removing the cable.


1. Push cable support bracket up with thumb and place cable
within “V” of bracket so that end of cable is next to cutting
blade, see Fig. 1.
Adjust depth of cutting blade to thickness of cable insulation
by turning the knurled screw, see Fig. 1.

NOTE: Care should be taken so that the cutting blade is not deep
enough to be nick or cut the strands of the cable. If the
strands appear to be nicked or cut, the blade should be
lowered to the proper depth.

 

 

 

2. Determine the length of insulation to be removed and mark
the point where the cut should be made. Push cable
support bracket up with thumb, see Fig.2. Insert the cable
between “V” of support bracket and insulation cutting
blade. Locate cable so that the mark is directly above the
cutting blade.

 

 

NOTE: ALTERNATE METHOD, SEE FIG. 3 Hold stripping tool with end of cable support bracket facing you. Place cable under end of cable support bracket locating length of insulation to be removed directly in front of cutting blade. Pull
stripping tool downward moving cable into the tool, under cable support bracket.

 

 

3. Rotate stripping tool completely around the cable to cut the insulation; then, repeat rotation in reverse direction, see Fig. 4.

 

 

4. Remove insulation by rotating lever to other end of slot. Hold it in that position, see Fig. 5.

5. Pull the stripping tool longitudinally over entire length of insulation to be removed, see Fig. 5.

 

 

6. Peel away insulation by inserting the cable support bracket into the cut line which was made in figure 5 above, see Fig. 6 .

 

 

7. For tough insulation, cut cable insulation in spiral form. After Step 4 rotate lever and place blade in a diagonal position (45°), and while holding this position, rotate tool around cable. Peel-off insulation, see Fig. 7.

 

 

 

B. REPLACING THE BLADE

 

CAUTION : BLADE IS SHARP, USE CARE WHEN REPLACING.

 

1. Push cable support bracket up with thumb, and loosen knurled screw completely. Remove spring, blade and washer.


2. The spare blade is located in bottom of handle. To retrieve spare blade, slide pin to side. Do not lift pin out of its seat.

 

3. Insert spare blade with unsharpened end into slot. Replace washer, spring and nut.

4. Follow Step A1 to adjust depth of cutting blade.

 

 

CAT.NO. BCS8-40

 

 

 

 

유사 적용사례를 포함하는 동영상자료

http://youtu.be/K9dj8XArM-8

 

 

 

 

  

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

+ Recent posts