'tip'에 해당되는 글 106건

  1. 2014.11.12 T&B TnB Wiring Duct Cover TY3CPG6 사양소개
  2. 2014.11.12 T&B TnB Wiring Duct TY3X3WPG6 사양소개
  3. 2014.11.01 Chalmit Light 샬밋 Fluorescent 제품라인업 소개
  4. 2014.10.21 Chalmit 샬밋 458 EPDM Floodlight 기술사양
  5. 2014.08.04 T&B, Liquidtight Flexible Cord & Cable Fittings, 2255 사양소개
  6. 2014.07.14 Ty-Met, Stainless steel, Releasable type cable tie, YRL-5-150-BC 제품소개
  7. 2014.07.10 Thomas&Betts(TnB,T&B), Manual Crimp Tool, ERG4001 사양소개
  8. 2014.07.08 KOPEX-EX Conduit System, Fitting Instructions for Non-Metallic Braided EXBQ 설치가이드
  9. 2014.07.08 KOPEX-EX Conduit System, Fitting Instructions for Non-Metallic EXPQ 설치가이드
  10. 2014.07.05 Hawke ATEX INLINE Connector, ControlEx Termination Hook up Procedure 자료
  11. 2014.07.05 Hawke Exd Connector, MK IV ControlEx 기술사양
  12. 2014.07.05 Hawke Exd Connector, InstrumEx 기술사양
  13. 2014.07.05 Hawke Live Demateable Connector, InstrumEx Termination Hook up Procedure 자료
  14. 2014.07.05 Hawke Power Connector, PowerEx Termination Hook up Procedure 자료
  15. 2014.07.05 Hawke Exd Connector, PowerEx 기술사양
  16. 2014.05.21 Thomas&Betts(T&B,TnB) RA723 사양소개
  17. 2014.05.21 Thomas&Betts(T&B,TnB) NVNV-M162-10 사양소개
  18. 2014.05.20 Thomas&Betts(T&B,TnB) D8-10 사양소개
  19. 2014.05.20 Thomas&Betts(T&B,TnB) Color-Keyed 256-30695-1302 사양소개
  20. 2014.05.20 Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360A 사양소개
  21. 2014.05.20 Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360B 사양소개
  22. 2014.05.20 Thomas&Betts(T&B,TnB) Ty-Rap TYS5200H 사양소개
  23. 2014.04.24 파나소닉 Panasonic UV-Curing Systems, ANUP5256 Series 단종소식
  24. 2014.04.09 호크 Hawke S-Series Enclosure Size 9 기술사양
  25. 2014.01.14 Hawke 호크 ICG653Universa Pl/ICG653UNIV P타입 기술사양
  26. 2013.11.28 T&B(TnB), Watertight, Flexible Connections Support Movement and Thermal Expansion 자료소개
  27. 2013.11.22 티앤비(티엔비), Power Connection & Control 종합카탈로그 CAT03 소개
  28. 2013.11.22 티앤비(티엔비), Wire & Cable Management 종합카탈로그 CAT01 소개
  29. 2013.11.21 티앤비(티엔비), T&B Fittings, Shureflex Nylon Liquidtight Conduit System 자료
  30. 2013.11.21 티앤비(티엔비), Harnessflex Protection for Critical Electrical & Electronic Cable CAT 2011 소개

T&B TnB Wiring Duct Cover TY3CPG6 사양소개

 

안녕하세요 TIATIP 입니다. 오늘 이 시간에는 Thomas&Betts 의 Wiring Duct Cover가운데 TY3CPG6 사양에 대해 살펴보도록 하겠습니다.

 

 

 

 

 

 

Thomas&Betts

T&B TnB Catalog Number : TY3CPG6

Wiring Duct Cover 

 

 

 

 

Features

- Wide fingers and slots increase rigidity and enable insertion of bundles. V-Shaped slot lead-in enables easier and faster wire installation. Rounded edges keep hands and wires free of abrasion.

- Non-slip cover does not slide easily and resists vibration. Flush cover attaches flush with sidewall for finished look.

- Dual score lines are designed to yield clean breakoffs at the base of the slot and the duct. Versatile North American and DIN Standard mounding holes enables same duct for multiple applications

 

 

 

 

Catalog Number must be completed by adding suffix G for Gray, W for White, B for Black, I for Intrinsic Blue. To order Adhesive-Backed duct, add suffix A. To order duct without mounting holes, add suffix NM to catalog number. Contact Customer Service for pricing and availability

 

 

 

 

Standard lengths are 6 feet

 

 

 

 

 

 

 

T&B TnB Wiring Duct Cover TY3CPG6 Technical Data

TY3CPG6.pdf

TnB Tyduct Overview.pdf

TnB Tyduct Specifications.pdf

TnB Tyduct Technical wideslot.pdf

TnB Tyduct Drawing.pdf

 

 

FYI : Specification are subject to change without notice.

소개된 제품 및 시스템의 사양, 재질, 치수, 기타 기재 내용은 제조공급사의 사정이나, 성능향상을 위해 예고 없이 단종, 대체되거나 변경되는 경우가 있으므로 양해해주시기 바랍니다. 기타 상세한 상담은 전문대리점을 통해 진행해 주시기 바랍니다. 고맙습니다.

 

 

 

 

  

국내 상담문의 및 기술지원

CUSTOMER  SUCCESS  IDK

deric@jadongwha.com

http://www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

T&B TnB Wiring Duct TY3X3WPG6 사양소개

 

안녕하세요 TIATIP 입니다. 오늘 이 시간에는 Thomas&Betts 의 Wiring Duct 가운데 TY3X3WPG6 사양에 대해 살펴보도록 하겠습니다.

 

 

 

 

 

Thomas&Betts

T&B TnB Catalog Number : TY3X3WPG6

Wiring Duct

 

 

 

 

Features

- Wide fingers and slots increase rigidity and enable insertion of bundles. V-Shaped slot lead-in enables easier and faster wire installation. Rounded edges keep hands and wires free of abrasion.

- Non-slip cover does not slide easily and resists vibration. Flush cover attaches flush with sidewall for finished look.

- Dual score lines are designed to yield clean breakoffs at the base of the slot and the duct. Versatile North American and DIN Standard mounding holes enables same duct for multiple applications

 

 

 

 

 

Catalog Number must be completed by adding suffix G for Gray, W for White, B for Black, I for Intrinsic Blue. To order Adhesive-Backed duct, add suffix A. To order duct without mounting holes, add suffix NM to catalog number. Contact Customer Service for pricing and availability

 

 

 

 

Standard lengths are 6 feet

 

 

 

 

  

T&B TnB Wiring Duct TY3X3WPG6 Technical Data

TY3X3WPG6.pdf

TnB Tyduct Overview.pdf

TnB Tyduct Specifications.pdf

TnB Tyduct Technical wideslot.pdf

TnB Tyduct Drawing.pdf

 

 

FYI : Specification are subject to change without notice.

소개된 제품 및 시스템의 사양, 재질, 치수, 기타 기재 내용은 제조공급사의 사정이나, 성능향상을 위해 예고 없이 단종, 대체되거나 변경되는 경우가 있으므로 양해해주시기 바랍니다. 기타 상세한 상담은 전문대리점을 통해 진행해 주시기 바랍니다. 고맙습니다.

 

 

 

 

 

 

 

국내 상담문의 및 기술지원

CUSTOMER  SUCCESS  IDK

deric@jadongwha.com

http://www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Chalmit Light 샬밋 Fluorescent 제품라인업 소개

 

안녕하세요 TIATIP 입니다.

오늘 이 시간에는 Chalmit Light 샬밋조명가운데 Fluorescent 타입의 제품군에는 어떠한 것들이 있는지 대략 살펴보도록 하겠습니다.

 

 

 

1. Zone 1

(1) Chalmit Protecta III Luminaire

Ex e Fluorescent / ATEX Category 2

 

 

 

(2) Chalmit Protecta III Emergency Luminaire

Ex e Fluorescent / ATEX Category 2

 

 

 

(3) Chalmit Protecta III Stainless Steel Emergency

Ex e Fluorescent / ATEX Category 2

 

 

 

(4) Chalmit Lomond Emergency Luminaire

Ex e Fluorescent / ATEX Category 2

 

 

 

(5) Chalmit Acclaim Recessible Luminaire

Ex e Fluorescent / ATEX Category 2

 

 

 

(6) Chalmit Curie Elite Recessible Luminaire

Ex e Fluorescent / ATEX Category 2

 

 

2. Zone 2

(1) Chalmit Sterling II Luminaire

Ex n Fluorescent / ATEX Category 3

 

 

 

(2) Chalmit Sterling II Emergency Luminaire

Ex n Fluorescent / ATEX Category 3

 

 

 

(3) Chalmit Sterling II Stainless Steel Luminaire

Ex n Fluorescent / ATEX Category 3

 

 

 

(4) Chalmit Sterling II Emergency Stainless Steel Luminaire

Ex n Fluorescent / ATEX Category 3

 

 

 

(5) Chalmit Protecta II Luminaire

Ex n Fluorescent / ATEX Category 3

 

3. Industrial

(1) Chalmit Protecta Luminaire

Surface Mounted Fluorscent

 

 

 

(2) Chalmit Protecta Emergency Luminaire

Surface Mounted Fluorescent

 

 

 

(3) Chalmit Protecta Stainless Steel Luminaire

Surface Mounted Fluorescent

 

 

 

(4) Chalmit Acclaim  Luminaire

Recessible Fluorescent

 

 

 

(5) Chalmit Sterling II Luminaire

Surface Mounted Fluorescent

 

 

 

(6) Chalmit Sterling II High Frequency Luminaire

Surface Mounted Fluorescent

 

 

 

(7) Chalmit Sterling II Stainless Steel Luminaire

Surface Mounted Fluorescent

 

 

 

(8) Chalmit Curie Luminaire

Recessible Fluorescent

 

 

(9) Chalmit Sterling II HF Stainless Steel

Surface Mounted Fluorescent

 

 

 

Technical Data

0.Chalmit Lighting Master CAT 20110611 02.pdf

 

Notice : Specification are subject to change without notice.

주의사항 : 소개된 제품 시스템의 사양, 재질, 치수, 기타 기재 내용은 제조공급사의 사정이나, 성능향상을 위해 예고 없이 단종, 대체되거나 변경되는 경우가 있으므로 양해를 부탁 드립니다. 기타 문의 상담은 하기 전문대리점을 통해 진행해 주시기 바랍니다.

국내 기술지원 및 구매상담

CUSTOMER SUCCESS IDK

CS CENTER 010.5353.9110

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Chalmit 샬밋 458 EPDM Floodlight 기술사양

 

안녕하세요 TIATIP입니다. 오늘 이 시간에는 샬밋 일반조명제품군 가운데 Chalmit 458 EPDM Floodling 에 대해 살펴보도록 하겠습니다.

 

 

Chalmit Lighting

458 EPDM Floodlight

Industrial Application

 

 

 

The Chalmit 458 is high wattage, weatherproof, robust EPDM floodlight is versitile in its mounting suitability as this is available in a base-mounted version (/B) and pole-mounted option (/P). The range has excellent vibration resistance making it ideal for use in hostile marine environments.

 

 

The Chalmit 458 is manufactured from EPDM rubber with a heavy duty borosilicate front glass and wire guard for maximum protection. The Chalmit 458 is suitable for GLS and hps lamps with maximum continuous operating temperature of +30°C.

Models with GLS lamps can operate at an ambient temperature as low as -40°C. A universal control gear box is required for models with hps lamps.
 
Available in 150W HPS, 250W HPS and 300W GLS lamp options.

 

 

 

CAT REF.

458I/150/HS

458I/250/HS

458I/300/GL

 

Technical Data

458 Industrial.pdf

 

Notice : Specification are subject to change without notice.

주의사항 : 소개된 제품 시스템의 사양, 재질, 치수, 기타 기재 내용은 제조공급사의 사정이나, 성능향상을 위해 예고 없이 단종, 대체되거나 변경되는 경우가 있으므로 양해를 부탁 드립니다. 기타 문의 상담은 하기 전문대리점을 통해 진행해 주시기 바랍니다

 

 

국내 기술지원 및 구매상담

CUSTOMER SUCCESS IDK

CS CENTER 010.5353.9110

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

T&B, Liquidtight Flexible Cord & Cable Fittings, 2255 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Flexible Cord & Cable Fittings 가운데, 2255 사양에 대해 살펴보도록 하겠습니다. 

 

Liquidtight Flexible Cord & Cable Fittings

 

 

 

 

Description :

1 in. 90 degree malleable iron liquidtight strain relief cord connector, cord range-.500-.625.

 

 

 

 

Technical Data

Flexible Cord Cable Fittings CAT.pdf

Flexible Cord Cable Fittings Spec.pdf

Portable Cord Selection Table.pdf

 

 

 

 

 

Application :

Suitable for use in hazardous locations where general purpose equipment is specifically permitted by NEC 501-4(b).

Meets Coast Guard CG293

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Ty-Met, Stainless steel, Releasable type cable tie, YRL-5-150-BC 제품소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Stainless steel, Releasable type cable tie, 150 x 5 mm, black Polyester 316 grade stainless steel, YRL-5-150-BC 에 대해 살펴보도록 하겠습니다.

 

Thomas&Betts

Ty-Met

Stainless Steel Ties

The Ulimate Solution

 

 

 

 

 

Description

Stainless steel ties with a unique buckle design, that allows the tie to be unfastened for re-use. Recommended for applications in extreme conditions and hazardous areas, indoor and outdoor, such as the petrochemical and food processing industries, power stations, mining, shipbuilding, offshore and other aggressive environments.

 

 

 

Technical Information

CAT No.: YRL-5-150-BC

Type : Releasable Type

Material : 316 Grade Stainless Steel

Coating : Polyester

Temperature Range : -80℃ to +150℃

Colour : Black

Halogen Free : Yes

UV-Resistant : Yes

TyMet Spec 01.pdf

 

 

 

The new Releasable Type stainless steel ties from Thomas & Betts
have a unique buckle design that allows the ties to be unfastened
for re-use.

 

 

• Releasable and re-usable
• Fast, easy and reliable installation - can be installed by hand
• The additional ears can be bent back over the fastened tie

   to increase the tensile strength

 

 

Approvals

Det Norske Veritas Approval : E-7508

Germanischer Lloyd Approval : 40 629-01 HH

 

 

 

 

Ordering Information

Length(mm) : 150

Width(mm) : 5

Thickness(mm) : 0.61

Max. Bundle Diameter(mm) : 35

Min. Tensile Strength(N) : 334

Quantity(Pieces) : 100

Packaging Type : Bag

Tooling : CT1-TB, CT2-TB, CT4-TB

Note : 1334 N tensile strength rating for DNV

 

 

 

 

CAT No. Releasable Type (Coated)

YRL-5-150-BC,YRL-5-230-BC,YRL-5-330-BC,YRL-5-450-BC

YRL-5-650-BC,YRL-10-150-BC,YRL-10-230-BC,YRL-10-330-BC

YRL-10-450-BC,YRL-10-650-BC,YRL-10-750-BC, 

YRL5150BC,YRL5230BC,YRL5330BC,YRL5450BC,YRL5650BC

YRL10150BC,YRL10230BC,YRL10330BC,YRL10450BC,YRL10650BC

YRL10750BC,Ty-Met,TyMet

 

 

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(TnB,T&B), Manual Crimp Tool, ERG4001 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 각종 터미널 압착에 사용되는 클램프 공구 ERG4001에 대해 살펴보도록 하겠습니다.

 

 

 

Thomas&Betts, T&B, TnB

Wire Termination Tools

Comfort Crimp® Compression Tools

ERG4001

Redesigned family of termination tools sets a new standard for manual crimping tools!

 

 

For Installing STA-KON Nylon and Vinyl Insulated Terminals, Disconnects, And Splices on Copper Wire, 22-10 AWG

 

CAUTION : Handles Non-Insulating, Do Not Crimp Energized Wires

 

 

Sta-Kon® Comfort Crimp® Compression Tools previously set the standard
for manual crimp tools. Now, Thomas & Betts engineers have made
a great line of tools even better with the newly redesigned Sta-Kon®
Comfort Crimp® Compression Tools. We kept all the performance
features that made the tools industry leaders such as the Shure-Stake®
mechanism and interchangeable dies with color-coded die nests, and
focused on creating the best possible user experience in terms of comfort
and reduction of strain.

 

 

 

Ergonomic handles position the user’s hands correctly to minimize the
risk of strain, and soft, over-molded grips cushion fingers and palm for
user comfort. A new Crimp-Assist™ foot stabilizes the tool when the
user needs to place it on a work surface for leverage to crimp larger
connectors. Best of all, the redesigned Comfort Crimp® tools require
25% less handle force to complete the crimp cycle than the previous
generation — and up to 75% less handle force than competing tools!

 

 

 

Requiring the lowest handle force of any tool in its class, the new Comfort
Crimp® family provides maximum comfort to installers, without sacrificing
the durability or performance associated with Thomas & Betts tools.

 

 

CAT No.

ERG4001, ERG4002, ERG4005, ERG4006, ERG4007, ERG4008

 

 

Technical Data

CAT03.08 StaKon Wire Termination Insulation.pdf

ERG4001 Drawing.pdf

ERG4001 Instruction Sheet.pdf

Stakon Die Selection Chart.pdf

Stakon Tool Selection Chart.pdf

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

KOPEX-EX Conduit System, Fitting Instructions for Non-Metallic Braided EXBQ and EXBB Conduit 설치가이드

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Ex'e'타입의 Conduit System과 관련하여, EXBQ시리즈의 Fitting과 EXBB Series의 Conduit의 설치가이드를 전해드립니다.

 

 

 

 

 

Thomas&Betts

KOPEX-Ex Conduit Systems

EXBB

EXBQ, EXBQM, EXBQA

 

 

Over Braided Conduit

EXBB Conduit Series

 

 

 

 

Straight Male Conduit Fitting

EXBQ Conduit Gland/Fitting Series

EXBQM & EXBQA Series

 

 

 

 

 

 

Wrap sellotape around conduit and cut to length required. Apply the “nut out” over the braiding before removing tape.

 

 

 

 

Remove tape and pull back braided sheath. Apply “nut in” so that approximately five convolutions protrude.

 

 

 

Apply seal with chamfered edge towards the “nut in” three corregations in from the end of the conduit.

 

 

 

Loosely assemble body into the “nut in.”
If using with a plain hole, fully tighten nut into body to secure gland on conduit.
If using with a threaded entry, leave nut loose to allow gland to freely rotate
about the conduit. Screw body into entry, then fully tighten nut.

 

 

 

Position braiding over steps of “nut in” and secure with “nut out” ensuring braid is trapped between the nuts.

 

 

Special Conditions for Safe Use:
When the gland is used for increased safety or dust protection, the entry of the enclosure and the female thread of the gland is to be sealed (in accordance with IEC60079-14) in order to maintain the ingress protection rating of the associated enclosure.

 

 

 

CAT Number

EXBB,EXBQ,EXBQM,EXBQA,EXBB0310, EXBB0330, EXBB0350,EXBB0410, EXBB0430, EXBB0450,EXBB0510, EXB0530, EXBB0550,EXBB0610, EXBB0630, EXBB0650,EXBB0710, EXBB0730, EXB0750,EXB0810, EXBB0830, EXBB0850,EXBQM0304, EXBQM0404, EXBQM0505, EXBQM0606, EXBQM0707, EXBQM0808,EXBQA0304, EXBQA0404, EXBQA0505, EXBQA0606, EXBQA0707, EXBQA0808,EXBQA0305

 

 

 

 

 

Installation Guide 

 

http://youtu.be/sLYP8cZvxZY

 

 

 

Technical Data

 

CAT02.06 KopexEx Hazardous Location Conduit Systems.pdf

CAT21.Adaptaflex and KopexEx.pdf

CAT26.02 KopexEx Stainless Steel Conduit Systems.pdf

DTS KOPEX Hazardous Area CAT02.pdf

DTS KOPEX Installation Guide.pdf

EXB EXBB Conduit Spec 20110522.pdf

EXBQ Fittings Spec 20120409.pdf

 

 

 

 

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

KOPEX-EX Conduit System, Fitting Instructions for Non-Metallic EXPQEXB Conduit 설치가이드

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Ex'e'타입의 Conduit System과 관련하여, EXPQ시리즈의 Fitting과 EXB Series의 Conduit의 설치가이드를 전해드립니다.

 

 

 

Thomas&Betts

KOPEX-Ex Conduit Systems

EXB

EXPQ, EXPQM, EXPQA

 

Anti-Static Conduit, EXB Conduit Series

 

 

 

 

 

Straight Male Conduit Fitting

EXPQ Conduit Gland/Fitting Series

EXPQM & EXPQA Series

 

 

 

 

 

 

Apply nut and seal over conduit, ensuring chamfered edge of seal is facing towards nut. Seal to be positioned three corrugations in from the end of the conduit.

 

 

 

If using with plain hole, fully tighten nut onto body to secure gland onto conduit.

 


If using with threaded entry, leave nut loose to allow gland to freely rotate about the conduit. Screw body into entry, then fully tighten nut to complete installation.

 

 

 

 

 

Installation Guide

 

http://youtu.be/duJ6vW-TV4g

 

 

CAT Number

EXB,EXPQ,EXPQM,EXPQA, EXB0310, EXB0330, EXB0350,EXB0410, EXB0430, EXB0450,EXB0510, EXB0530, EXB0550,EXB0610, EXB0630, EXB0650,EXB0710, EXB0730, EXB0750,EXB0810, EXB0830, EXB0850,EXPQM0304, EXPQM0404, EXPQM0505, EXPQM0606, EXPQM0707, EXPQM0808,EXPQA0304, EXPQA0404, EXPQA0505, EXPQA0606, EXPQA0707, EXPQA0808,EXPQA0305

 

 

 

 

 

Technical Data

CAT02.06 KopexEx Hazardous Location Conduit Systems.pdf

CAT21.Adaptaflex and KopexEx.pdf

CAT26.02 KopexEx Stainless Steel Conduit Systems.pdf

DTS KOPEX Hazardous Area CAT02.pdf

EXB EXBB Conduit Spec 20110522.pdf

EXPQ Conduit Spec 20110121.pdf

 

 

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke ATEX INLINE Connector, ControlEx Termination Hook up Procedure 자료

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Hawke ATEX INLINE Connector, ControlEx 시리즈의 Termination Hook up Procedure 관련 자료를 소개합니다. 

 

 

 

HAWKE

ControlEx Termination Procedure

 

IMPORTANT NOTE


1. Hawke International does not recommend the use of their ControlEx Connectors in applications where rigid PVC/SWA/PVC power cabling (typically to BS 6346 standards) is used in portable / semi-portable applications.


2. Barrier type glands must be fitted to flexible power and loose filled control cabling entering the connectors to maintain the Exd protection concept and to reduce the potential for core movements within the cable being transferred to the connector’s internal components. Where connectors are terminated to topside umbilical cables, or portable connectors, a barrier type cable gland should always be used.


3. Hawke Ex Connector products are designed to be used in multi-voltage applications in circuits up to 660V AC/DC. It is
possible that on certain installations, there may be a mix of applications utilising different voltages on the Connector
products. In these instances, the installer / circuit designer must ensure that the plugs and sockets, or their associated
cabling, is clearly marked with the correct circuit voltage and current rating to ensure that the equipment being supplied is
matched correctly with the supply voltage. The variable insert positions which are a feature of the Connectors may also be
used to provide additional means of safety in these applications.

 

ControlEx Hook Up Procedure

 

1. Remove the CP/CR connector assembly, electrical insert and cable gland
(sold separately) from their packaging.


2. Terminate the cable into the cable gland in accordance with the manufacturer’s Instructions. Ensure a minimum tail length of 130mm.

 


 

3. Unscrew the rear engaging nut from the connector shell, removing the rear shell and keyway tube.

 

  

4. Slide the rear engaging nut over the rear shell as shown and screw the rear shell onto the entry thread of the cable gland ensuring there is a sealing washer between the gland and rear shell. A small amount of Loctite 638
or equivalent can be added to the cable gland thread at this stage to further help prevent loosening of the cable gland in portable applications.

 


Where a thread adaptor is being used, ensure a suitable IP seal is fitted between the cable gland and thread adaptor, and thread adaptor & running coupler. If the thread adaptor has an integral O-Ring, please ensure this makes full contact with the cable gland and running coupler to maintain the IP
protection. Check to ensure the captive O-Ring seal on the rear shell is in place and is undamaged

 

If the tab washer is being used, ensure this is fitted in the orientation shown. Use the flats on the rear shell to further tighten.

 

 

 

 

5. Cut the conductors to the length shown in the table below.

 

 

Note: Maximum tolerance is to allow for twisted cables and placement of cores within connector shell. If core spacing relative to insert numbering does not require excess core, use minimum cut lengths.

 

6. Strip back the insulation from the conductor’s as shown

 

 

 

 

7. Proceed to step 8 if internal earthing is not required.

 


NOTE: If internal earthing is not being used, the internal earth crimp must not be fitted and the grub screw in the rear shell must be removed

 


If earthing is required slide the internal crimp (supplied with CP/CR inserts) over the earth conductor and crimp using suitable tool. The stud can then be fitted into the rear shell and fastened using the grub screw shown. The stud on the earth crimp should not protrude from the outer diameter of the rear shell. Adjust if necessary.

 

 

8. a) Solder inserts – black (1.5 – 35mm²). Tin the conductors and fill the solder cups on the back of the inserts with solder as required Solder conductors in place and remove any solder spikes/excess from the solder cup. It is advised that heat shrink should be fitted over the connection at this point

b) Solder inserts – white (1.5 – 4mm2). As above, however, inserts should be soldered outside of the insert body and not fully assembled. If the contacts are to be solder terminated to the conductors, this must be done prior to insertion
through the rear contact retainer. It is advised that heat shrink should be fitted over the connection at this point Then follow (c ii & iii).


c) Crimp Inserts (1.5 – 4mm²) – white.

 

i) Crimp the conductors into the contacts using Weidmuller CTX CM 1.6/2.5 crimp tool HCT1, or Astro Crimp Tool HCT2. For 0.75 to 1.5mm² conductors use the 1.5 die. For 1.6 to 4mm² use the 2.5 die. It is advised that heat shrink should be fitted over the connection at this point


ii) Feed the contacts through the required numbered hole on the rear contact retainer and slide the insertion tool over the contacts up to the groove (one end for pin and one for socket). Clip the groove on the contact into position in the rear contact retainer with the tool.

 

 

 

iii) Align the main pip on the rear contact retainer with the key on the front contact retainer and slide over the contacts into position. Ensure the 2 smaller pips are also in line

 

 

d) Crimp Inserts (6 – 35mm²) – black. Undo the grub screws on the crimp barrels and slide them off the back of the contacts. Slide the conductors into the back of the barrel. Orientate the barrel so that the grub screws are pointing
outwards and crimp with a suitable crimp tool.


Push the barrels back onto the rear of the contacts and tighten grub screw into the groove on the contact. Back off grub screw half a turn on crimp barrels of 10mm² or larger to allow them to slide up and down the contact slightly

 

 

 

 

 

9. Clip spacer tube over conductors. Bend conductors slightly so that there is no or minimal gap between the insert/spacer tube and rear shell. On crimp insert of 10mm² or larger, slide the crimp barrels up and down the contacts to achieve this and then lock them in place by tightening the grub screw’s on the crimp barrels.

The insert has 3 pips, shown below, which should be located as shown. The main centre keyway should align with the centre of the spacer tube

 

 

 


NOTE: If being used on offshore topside applications where extreme temperature fluctuations or extreme levels of humidity may be present, it is advisable to use Dow Corning 4 Electrical Insulating Compound within the spacer tube to help prevent any possible humidity build-up. See point 15 below

 

 

10. Looking from the front of the connector shell, align the key on the insert to the required key inside the connector and slide the whole assembly into the shell. The EX16 connector has 3 keyways, and all other connectors have 5 possible keyways

 

 

 

 

11. Fully screw the rear engaging nut onto the thread on the connector shell, do not rotate the connector shell during this process. Tighten grub screw in rear engaging nut. There should be a gap visible of no more than 1mm between running coupler and shell

 

 

 

 

12. If the tab washer is being used, fix the tab using the button head screw to the rear engaging nut. Bend the tabs over the
flats of the cable gland.


13. If being used, terminate the external earth to the ring terminal crimp provided with the insert. Remove the button head
screw and spring washer from the rear engaging nut. Attach the crimp to the rear engaging nut as shown above


14. The connector is now ready for use. Please refer to the ‘Hook Up’ procedure.

15. If additional protection is required due to extreme atmospheric conditions, before inserting the assembled connector insert and spacer tube into the connector shell (step 10 above) Dow Corning 4 Electrical Insulating Compound can be used to fill the spacer tube. It is recommended that the running coupler be filled, along with the inner face of the insert to ensure no humidity can affect the contacts

 

 

ControlEx MK IV Connector Hook Up Procedure

 

Before commencing hook up, a visual inspection should be carried out on the cable / gland / connector assembly. The assembly should be checked to ensure that all of the assembly components are tight. If the assembly components have loosened during transportation / cable installation, they should be retightened in accordance with the relevant assembly instruction sheets without twisting the cable in the cable gland / connector assembly.

 

Areas to be checked:

 

 

 

 

NB: These areas should also be checked as part of a routine maintenance programme.

 

1) Turn off the power to the connectors.
2) Ensure the connectors are both set to the same keying position number and are of the same insert type.

 

 

 

 

3) Engage the CP connector with the BR / CR connector and align the key on the CP connector to the keyway on the BR / CR connector.

 

 

engaging nut clockwise onto the BR/CR shell. If the engaging nut will not screw on more than half a
turn, then the connectors are set to different keying positions.

 

 

5) Tighten the grub screw on the engaging nut.

 

6) If the optional locking pin is being used, this should be fitted at this stage, once the connectors are fully mated.

 

 

7) To disconnect, turn off the power, slacken the tightened grub screw, turn the engaging nut anticlockwise and remove the connector. If power is to be put through the connectors whilst de-mated, then a flameproof cap (available separately) must be fitted.

 

 

 

 

Technical Data

ControlEx MKIV Spec.pdf

ControlEx Spec.pdf

ControlEx MKIV Hookup Procedure 20131105.pdf

ControlEx MKIV Hookup Procedure 20131218.pdf

ControlEx Hook up procedure 20091202.pdf

ControlEx Inline connector termination 20091202.pdf

0.Ex Connectors Master Catalogue 20130819.pdf

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke Exd Connector, MK IV ControlEx 기술사양

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 호크 방폭커넥터 제품군 가운데, Contrl 관련 애플리케이션에 적합한 Hawke MK IV ControlEx 시리즈를 살펴보도록 하겠습니다.

 

 

 

HAWKE

Range For Harsh and Hazardous Locations

Hazardous Area Connector

MK IV ControlEx

IECEx/ATEX Certificate 

 

Note: Inline connector receptacle (CR) also available

 

 

Overview

 

The 4th generation ControlEx has been designed as a result of over 20 years of plug-and-socket experience. Manufactured in Stainless steel, the connectors provide unrivalled durability in hostile environments.

 

Both ATEX/IECEX, GOST & NEC certified, the connectors are Exd rated with an Ingress Protection rating of IP66 / IP67 and have industry leading DTS01 deluge protection.

 

 

 

 

The wide range of insert variables can handle up to 60 cores.

 

Other improvements include an all-new padlock facility, allowing the connectors to be securely locked to prevent accidental un-plugging of equipment and improved secure cap fixings.

 

The 4th generation ControlEx maintains many of the original features which made its predecessor extremely popular, including a variable keying system to prevent accidental cross-mating, modular gold-plated field crimpable inserts for ease of wiring and a fully inspectable flameproof barrier providing direct inspection of the flameproof seal.

 

 

 

 

 

Tamb: -40°C to +60°C.

II2 GD Exd IIC Gb, Extb IIIC T95Db.

IP66, 67

DTS01 deluge protected.

Certificate No's Baseefa12ATEX0014X & IECEx BAS 12.0006X.

 

ControlEx Features

 

(1) Easy Fieldwireable
Pin and socket inserts are numbered front and back to assist wiring and avoid
termination errors. Crimp and solder inserts available.

 

 

(2) Internal Keyway Spacer

Eases accessibility for termination as tube fitted after termination complete,
along with allowing easy installation into the required keyed position (See (4))

 

 

(3) Locking Pin
Optional locking pin provides the facility for mated connectors to be permanently
locked, via the use of a padlock, ensuring they cannot be separated under load. (Padlock not supplied)

 

 

 

 

(4) Keying Position
The unique visual 5 position insert keying system (3 on Ex16) along with the integral machined keyways prevent contact damage and ensures safe use by eliminating the possibility of misconnection of adjacent circuits.

 

 

 

(5) Running Coupler
Allows the connector to be installed onto a pre-assembled cable gland. Connector is rear loading and includes locking engaging nut.

  

 

 

(6) Acme Thread at Mating Interface
Unique ACME thread offers a smooth and quick fully mating action.

 

 

 

(7) Fully Inspectable Flameproof Barrier
Provides direct inspection of the flameproof seal and offers users the peace of mind that the connector is safe for installation.

 

 

 

(8) Anti-Rotation Device
Connector plugs and receptacles come complete with anti-rotation ring, which
when fitted between the connector and gland, helps to eliminate the possibility of the gland loosening, locking this in position.

 

 

 

 

 

Technical Data

 

ControlEx MKIV Spec.pdf

ControlEx MKIV Hookup Procedure 01.pdf

ControlEx MKIV Hookup Procedure 02.pdf

0.Ex Connectors Master Catalogue 20130819.pdf

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke Exd Connector, InstrumEx 기술사양

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 호크 방폭커넥터 제품군 가운데, Instrument 연결 애플리케이션에 적합한 Hawke InstrumEx 시리즈를 살펴보도록 하겠습니다.

 

 

HAWKE

Range For Harsh and Hazardous Locations

Hazardous Area Connector

InstrumEx

IECEx/ATEX Certificate 

 

Overview

This revolutionary design allows the live mate and de-mating of signal and low power in hazardous areas safely and quickly. The InstrumEx connector is available with two insert options:

 

 

 

The 4-way option will accept cores ranging between 0.5mm² and 2.5mm² and can operate up to a maximum current of 10A (AC1) at 250V AC & 2.5A (DC1) 60V DC.

 

The 8-way option, designed predominantly for Ethernet applications, will accept cores ranging between 0.14mm² and 0.37mm² and can carry 1A (AC1) at 60V AC & 0.5A (DC1)60V DC. InstrumEx connectors include an integral Hawke cable gland for easy termination of both armoured and un-armoured cables.

 

 

 

 

Tamb: -40°C to +60°C.

II2 GD Exd IIC ExtD T85.

IP66, 67

DTS01 deluge protected.

 

 

 

Technical Data

InstrumEx Spec.pdf

InstrumEx BRO 200808XX.pdf

InstrumEx Manual 20140403.pdf

0.Ex Connectors Master Catalogue 20130819.pdf

 

  

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke Live Demateable Connector, InstrumEx Termination Hook up Procedure 자료

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Hawke Live Demateable Connector, InstrumEx 시리즈의 Termination Hook up Procedure 관련 자료를 소개합니다.

 

 

 

 

HAWKE

InstrumEx Termination Procedure

 

IMPORTANT NOTE

1. Hawke International does not recommend the use of their InstrumEx Connectors in applications where rigid PVC/SWA/PVC power cabling (typically to BS 6346 standards) is used in portable/semi-portable applications.


 

2. Hawke International recommends that barrier type glands are fitted to flexible power and loose filled control cabling entering the connectors to maintain the Exd protection concept and to reduce the potential for core movements within the cable being transferred to the connector’s internal components.


 

3. Hawke Ex Connector products are designed to be used in multi-voltage applications in circuits: 4 way up to 250V AC, 4 way up to 60V DC and 8 way up to 60V AC/DC. It is possible that on certain installations, there may be a mix of applications utilising different voltages on the Connector products. In these instances, the installer / circuit designer must ensure that the plugs and sockets, or their associated cabling, is clearly marked with the correct circuit voltage and current rating to ensure that the equipment being supplied is matched correctly with the supply voltage. The variable insert positions which are a feature of the Connectors may also be used to provide additional means of safety in these applications.

 

 

 

 

CP / CR PROCEDURE


1) Unscrew the middle nut and back nut from the connector body and remove the armour clamping ring, spigot and insert. If you have purchased a connector with the optional backnut clamp and / or flange, slide these down the cable now (clamp first).

 

 

2) Remove the two seal assembly’s from the box and choose the required seal to suit the diameter of the cable outer jacket.

 

 

 

3) Insert the seal into the back nut, ensuring that the flange on the seal goes past the thread as shown.

 

 

 

 

 

4) Screw the back nut onto the middle nut. Do not compress the seal at this stage.

 

 

 

5) Slide the middle nut, backnut and armour clamping ring over the cable ensuring that the clamping ring is pointing in the required direction for the size of armour / braid. The alternative ring is supplied in the box.

 

                          

 

 

 

6) Strip back the outer jacket and armour (if present) as shown below.

 

 

 

7) Strip back the inner sheath level with the armour to expose the insulated conductors as shown below. If unarmoured, strip back to the outer jacket.

 

 

 

 

 

ARMOURED / BRAIDED CABLE


8) Push the inner sheath of the cable through the spigot.
Spread the armour / braid over the spigot until the end of the armour / braid is up against the shoulder of the spigot. Position the armour clamping ring onto the armour/braid.

 

 

 

9) Place the connector body over the spigot engaging the octagonal portion of the spigot. Move the middle nut up to meet the connector body. Place a 27 A/F spanner on the flats of the connector body and hold it in position.
Hand tighten the middle nut to the connector body, then turn a further ½ to ¾ turn with a 27 A/F spanner.

 

 

 

10) Unscrew the middle nut and visually inspect the armour has been  successfully clamped between the armour spigot and the clamping ring.

 

 

 

 

UNARMOURED CABLE
(If earth is to be terminated to connector shell. Otherwise proceed to step 15)


11) Strip back the earth conductor as shown below. If the earth is being carried through a contact as well as being connected to the shell, see fig b.

 

 

 

12) Crimp the flat blade earth crimp onto the earth conductor as shown below. Ensure the blade of the crimp is outermost as shown and that the crimp is pushed all the way up to the insulation of the earth conductor.

 

 

13) Push the conductors through the spigot and place the blade of the crimp on the taper of the spigot.

 

 

 

 

 

 


the blade of the crimp and lock into position by following steps 9 and 10 of the armoured / braided cable procedure.

 

15) Strip back the conductors as shown below.

 

 

 

 

 16) Remove the contacts from the contact retainers. Crimp the contacts onto the conductors using the Hawke crimp tool only (part number 901849). Ensure that the insulation of the conductor is up against the shoulder of the contact. When terminating 0.5mm² or 1.5mm² wire, ensure the conductor is pushed all the way into the smaller hole of the contact and that the contact is square in the crimp tool.


CAUTION: EXCESSIVE FORCE MAY BEND THE CONTACTS


Alternatively, conductors may be soldered into the contacts. Ensure that the cable installation is the same on the mating half. Hawke recommends that wiring details are placed on the cable outer jacket near to the connector.

 

 

17) Splay out the contacts and fit them through the slots in the rear contact retainer, ensuring they line up with the relevant numbered hole on the front contact retainer (ensure keys are aligned - see step 18). Unused contacts
should be omitted if not required to ease assembly.

 

 

 

18) Slide the front contact retainer over the contacts and snap into place with the rear contact retainer. Push the clips of the rear contact retainer firmly down to ensure they are not protruding (will only fit in the correct orientation).

 

 

19) Slide the insert into the connector body, aligning the half round key on the rear contact retainer with the required half round keyway in the connector body. (The colour coded or numbered keying position is shown on the front of the connector body. No colour coding or numbering for default 12 o’clock position – see picture inset). It should be noted that colour coded and numbered connector bodies are mutually interchangeable. Push the octagonal portion of the spigot into the connector body.

 

 

20) Slide the middle nut over the clamp / spigot and hand tighten onto the connector body, then further tighten ½ to ¾ of a turn with a 27 A/F spanner while holding the front shell with a 27 A/F spanner

 

 

 

 

 

21) Hand tighten the backnut onto the middle nut. Further tighten 1 to 1 ½ turns with a 27 A/F spanner while holding the middle nut with a spanner.

 

 

 

22) If the optional mounting flange is required, slide the flange over the backnut and position on the middle nut. Align the grub screw with one of the flats and tighten. If the flange is being used on a CR connector, it may also be
placed on the connector body as shown over.

 

 

23) If the optional cable clamp has been purchased, tighten the screws on the clamping bars equally until the clamping bars touch the cable. Tighten each screw a further 2-4 turns or until adequately clamped.


DO NOT OVERTIGHTEN AS THIS COULD DAMAGE THE CABLE.


If the cable clamp is being used with unarmoured cable, the connector should be earthed via the crimp with a 4mm² conductor.

 

 

 


24) Screw the cap back onto the connector. Stick the corresponding round colour coded / numbered sticker onto label in the circular space provided.
(white = 12 o’clock / Position 1)

 

 

25) The connector is now ready for hook up. Please refer to the hook up procedure.

 

 

BR PROCEDURE
1) The BR connector is supplied ready terminated with tails.
Simply fit into suitable junction box / equipment as required. To maintain the IP rating of the equipment, a sealing washer should be used (available separately) as shown below.

 

 

2) Terminate the conductors and earth wire inside the junction box / equipment.


3) The connector may also be earthed externally via the crimp with a 4mm² conductor if required.

 

 

4) The connector is now ready for hook up. Please refer to the hook up procedure.

 

HOOK UP PROCEDURE

 

WARNING:
Only the socket insert is allowed to remain energised while de-mated. If being used with bi-directional signals, isolate elswhere before connecting / disconnecting.

 

Before commencing hook up, a visual inspection should be carried out on the cable / connector assembly. The assembly should be checked to ensure that all of the assembly components are tight. If the assembly components have
loosened during transportation / cable installation, they should be retightened in accordance with the relevant assembly instruction sheets without twisting the cable in the connector assembly.

 

1) Remove connector caps.


2) Ensure the connectors are both set to the same keying position colour or numbered (no colour or number for default 12 o’clock position on BR/CR) and are of the same insert type.
It should be noted that colour coded and numbered connector bodies are mutually interchangeable.

 

 

3) Engage the CP connector with the BR / CR connector and align the keyway on the CP connector to the key on the BR / CR connector.

 

 

 

4) Engage the two connectors by screwing the engaging nut clockwise without interruption onto the BR/CR shell. If the threads will not engage, the connectors
are set to different keying positions.

 

 

5) If anti-vibration protection is required, tighten the grub screw on the CP shell.

 

 

6) To disconnect, slacken the tightened grub screw, turn the engaging nut anti-clockwise and remove the connector. Fit the caps.

 

Technical Data

InstrumEx Spec.pdf

InstrumEx Manual 20140403.pdf

InstrumEx BRO 200808XX.pdf

0.Ex Connectors Master Catalogue 20130819.pdf

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke Power Connector, PowerEx Termination Hook up Procedure 자료

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Hawke Power Connector, PowerEx 시리즈의 Termination Hook up Procedure 관련 자료를 소개합니다.

 

 

Hawke

PowerEx Termination Procedure

 

IMPORTANT NOTE
Hawke International does not recommend the use of their Power Connectors in applications where rigid PVC/SWA/PVC power cabling (typically to BS 6346 standards) is used in portable / semi-portable applications.


In addition, Hawke recommends that barrier type glands are fitted to flexible power and loose filled control cabling entering the connectors to maintain the Exd protection concept and to reduce the potential for core movements within the cable being transferred to the connector’s internal components. 

 

 

 

 

CP / CR PROCEDURE
1) Terminate the cable into the Exd cable gland as per the manufacturer’s instructions. Consider at this stage the relative position of the phases.

 

 

 

2) Cut the conductors to the lengths shown. (For earth conductors which are being terminated to the earth ring (see step 6) but not carried through the contact, cut back X = 100mm for all sizes, see 10 - 13)

 

 

 

3) Strip back the insulation as shown. (For all earth conductors terminated via the internal earth ring, cut back the insulation flush with the gland entry thread, see 10 - 13).

 

 

 

4) Unscrew the rear engaging nut from the CP / CR shell. Remove the rear shell, spacer tube and insert from the CP / CR shell.

 

 

5) a) CONTACT SIZES 50 - 240mm².

Remove the screws from the front of the contacts only and push the crimp lugs out of the insert.

 

 

b) CONTACT SIZES 300 – 630mm².

Remove the screw from the plastic housing and remove the contact from inside.

 

 

 

6) Remove the internal earth ring from the rear shell sub assembly by backing off the 2 grub screws on the flats. If internal earthing is not required, the internal earth ring assembly along with the fixing grub screws should be discarded.

 

 

 

7) Crimp the lugs or contacts onto the conductors

(excluding internal earth wire if being used) using suitable crimp tool. (Hawke recommend Elpress crimp tools).
Contact sizes of 185mm² and larger should be adjacently double crimped as shown.

 


 

8) Feed the conductors through the rear shell assembly and screw this onto the cable gland entry thread ensuring the sealing washer is present.

 

 

 

9) Measure the distance from the front of the rear shell to the end of the crimp lug (50 – 240mm²) or contact (300 - 630mm²). It should be as shown. If not, remove the rear shell and add or remove the spacer washers supplied to get the required length. At least 1 washer must be present to maintain IP rating.

 

 

 

Internal earth procedure (skip to step 13 if not used or you have single phase connector).


10) Slide the internal earth ring down over the conductors with the lug going over the bare earth wire.

 

 

 

 

11) Position the internal earth ring inside the rear shell and tighten the grub screws into the groove on the earth ring. Excessive force could distort rear shell.

 

 

 

 

 

12) Tighten the 2 grub screws on the internal earth lug into the earth conductor as tight as possible so that the earth wire is sufficiently clamped. If earth is to be carried through to a contact, crimp contact prior to tightening grub screws.

 

 

 

 

13) Slide the spacer tube over the conductors and onto the rear shell.

 

 

 

 

14) a) CONTACT SIZES 50 - 240mm².
Push the insert assembly fully onto the crimp lugs. The insert should push inside the spacer tube. Refit the 4 screws into the ends of the contacts. Ensure these are fully tightened.

 

 

 

 

b) CONTACT SIZES 300 – 630mm².
Push the rear retainer over the contact. Place the split tube around the contact. Slide the front contact retainer over the contact and split tube. Slide the rear contact retainer over the rear of the contact and tighten the screw fully.

 

 

 

15) Slide the CP / CR shell over the insert and line the yellow dot on the insert up with the required keying position 1 to 5 marked on the CP / CR shell.

 

 

16) Screw the rear engaging nut fully onto the CP / CR shell.
Measure the distance between the front of the rear engaging nut to the back of the engaging nut which should be no greater than the distance shown.

 

 

 

17) Tighten down the 2 grub screws on the rear engaging nut.

 

 

 

18) Terminate the equipotential external earth to the ring terminal crimp provided if applicable. Remove the button head screw, spring washer and crimp from the rear engaging nut. Crimp the external earth wire into the crimp and reassemble.

 

 

 

19) Refit the protective or flameproof cap if applicable.

 

 

 

20) The connector is now ready for installation. Please refer to the hook up procedure.

 

 

 

HOOK UP PROCEDURE
Before commencing hook up, a visual inspection should be carried out on the cable / gland / connector assembly. The assembly should be checked to ensure that all of the assembly components are tight. If the assembly  components have loosened during transportation/cable installation, they should be retightened in accordance with the relevant assembly instruction sheets without twisting the cable in the cable gland/connector assembly. No hazardous gases should be present.

 

1) Turn off the power to the connectors.


2) Ensure the connectors are both set to the same keying position number, are of the same insert type and phase orientation.

 

 

3) Engage the CP connector with the BR / CR connector and align the key on the CP connector to the keyway on the BR / CR connector.

 

 

4) Engage the two connectors by screwing the engaging nut clockwise onto the BR/CR shell. If the engaging nut will not screw on more than half a turn, then the connectors are set to different keying positions.

 

 

5) Fully tighten the engaging nut with strap wrench if necessary and then tighten the grub screw on the engaging nut.

 

 

 

6) To disconnect, turn off the power (no hazardous gases should be present), slacken the tightened grub screw, turn the engaging nut anti-clockwise and remove the connector. If power is to be put through the connectors whilst demated, then a flameproof cap (available separately) must be fitted.

 

 

Technical Data

PowerEx Spec.pdf

PowerEx Manual 20070619.pdf

0.Ex Connectors Master Catalogue 20130819.pdf

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke Exd Connector, PowerEx 기술사양

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 호크 방폭커넥터 제품군 가운데, Power 연결 애플리케이션에 적합한 Hawke PowerEx 시리즈를 살펴보도록 하겠습니다.

HAWKE

Range For Harsh and Hazardous Locations

Hazardous Area Connector

PowerEx

IECEx/ATEX Certificate 

 

Overview

The PowerEx range of connectors have been designed specifically for the extremely demanding requirements of higher power applications.

 

 

 

Inserts are available with 1 to 4 contacts with a conductor acceptance range of between 50mm2 and 630mm2 operating up to 780A and 750V as standard. Other voltages available on special request.

 

 

Tamb: -40°C to +60°C.

II2 GD Exd IIC ExtD T85.

IP66, 67

DTS01 deluge protected.

 

 

 

 

Hawke Exd Connector Range For Harsh and Hazardous Locations, PowerEx

 

Technical Data

PowerEx Spec.pdf

PowerEx Manual 20070619.pdf

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) RA723 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) RA723 사양에 대해 살펴보도록 하겠습니다. 

 

 

Ring Terminal

T&B Catalog Number : RA723

UPC Number : 78621019923

 

  

Description

Insulated Nylon Ring Terminal For Wire Range 22-16 Stud Size 5/16, Red, Military Specified (MIL-SPEC MS25036-104)

 

Features

Self-insulated with high dieletric-strength nylon sleeves. An inner bronze insulation grip sleeve lengthens the flexing radius of the conductor and eliminates conductor creep.

 

 

 

 

CAT No.

RZ22-2**, RZ22-4**, RZ22-6**, RZ22-8**, RZ22-10**, RAX23*, RAX43*

RAX63*, RAX83*, RAX103*, RA18-4, RA323, RA333, RA18-6, RA853, RA18-8, RA833, RA18-8, RA833, RA863, RA18-10, RA873, RA18-14, RA713, RA18-516, RA723, RA18-38, RA733, RA18-12, RA753, RB14-4,RB1323,RB14-6,RB853,RB1333,RB14-8,RB863,RB14-10,RB873, RB14-14,RB713,RB14-516,RB723,RB14-38,RB733,RB14-12,RB753,RC10-6,RC333,RC10-8,RC863,RC10-10,RC363,RC10-14,RC713,RC10-516,RC703,RC10-38,RC733,RC10-12,RC753

RB14-4X,RB14-6X,RB854,RB14-8X,RB864,RB14-10X,ER4001, RB874,RB14-14X,RB714,RB14-516X,RB724,RB14-38X,RB734RC10-6X,RC334,RC10-8X,RC864,RC10-10X,RC364,RC10-14X,RC714, RC10-516X,RC704,RC10-38X,RC734,RC10-12X

MIL-T-7928 MS-25036-101, T&B CAT No. RA333,
MIL-T-7928 MS-25036-102, T&B CAT No.  RA853,
MIL-T-7928 MS-25036-103, T&B CAT No.  RA873,
MIL-T-7928 MS-25036-104, T&B CAT No.  RA723,
MIL-T-7928 MS-25036-105, T&B CAT No.  RA733,
MIL-T-7928 MS-25036-106, T&B CAT No.  RB1333,
MIL-T-7928 MS-25036-107, T&B CAT No.  RB853,
MIL-T-7928 MS-25036-108, T&B CAT No.  RB873,
MIL-T-7928 MS-25036-109, T&B CAT No.  RB723,
MIL-T-7928 MS-25036-110, T&B CAT No.  RB733,
MIL-T-7928 MS-25036-111, T&B CAT No.  RC333,
MIL-T-7928 MS-25036-112, T&B CAT No.  RC363,
MIL-T-7928 MS-25036-113, T&B CAT No.  RC703,
MIL-T-7928 MS-25036-114, T&B CAT No.  RC733,
MIL-T-7928 MS-25036-115, T&B CAT No.  RD10361,
MIL-T-7928 MS-25036-116, T&B CAT No.  RD10711,
MIL-T-7928 MS-25036-117, T&B CAT No.  RD10721,
MIL-T-7928 MS-25036-118, T&B CAT No.  RD10731,
MIL-T-7928 MS-25036-119, T&B CAT No.  RE10261,
MIL-T-7928 MS-25036-120, T&B CAT No.  RE10711,
MIL-T-7928 MS-25036-121, T&B CAT No.  RE10721,
MIL-T-7928 MS-25036-122, T&B CAT No.  RE10731,
MIL-T-7928 MS-25036-123, T&B CAT No.  RF10711,
MIL-T-7928 MS-25036-124, T&B CAT No.  RF10721,
MIL-T-7928 MS-25036-125, T&B CAT No.  RF10731,
MIL-T-7928 MS-25036-126, T&B CAT No.  RG9711,
MIL-T-7928 MS-25036-127, T&B CAT No.  RG9731,
MIL-T-7928 MS-25036-128, T&B CAT No.  RG9751,
MIL-T-7928 MS-25036-129, T&B CAT No.  RH9711,
MIL-T-7928 MS-25036-130, T&B CAT No.  RH9731,
MIL-T-7928 MS-25036-131, T&B CAT No.  RH9751,
MIL-T-7928 MS-25036-132, T&B CAT No.  RJ9711,
MIL-T-7928 MS-25036-133, T&B CAT No.  RJ9731,
MIL-T-7928 MS-25036-135, T&B CAT No.  RK9721,
MIL-T-7928 MS-25036-136, T&B CAT No.  RK9731,
MIL-T-7928 MS-25036-137, T&B CAT No.  RK9751,
MIL-T-7928 MS-25036-138, T&B CAT No.  RL9731,
MIL-T-7928 MS-25036-139, T&B CAT No.  RL9751,
MIL-T-7928 MS-25036-140, T&B CAT No.  RM9731,
MIL-T-7928 MS-25036-141, T&B CAT No.  RM9751,
MIL-T-7928 MS-25036-142, T&B CAT No.  —,
MIL-T-7928 MS-25036-143, T&B CAT No.  —,
MIL-T-7928 MS-25036-144, T&B CAT No.  —,
MIL-T-7928 MS-25036-145, T&B CAT No.  —,
MIL-T-7928 MS-25036-146, T&B CAT No.  —,
MIL-T-7928 MS-25036-147, T&B CAT No.  —,
MIL-T-7928 MS-25036-148, T&B CAT No.  RA323,
MIL-T-7928 MS-25036-149, T&B CAT No.  RA863,
MIL-T-7928 MS-25036-150, T&B CAT No.  RA713,
MIL-T-7928 MS-25036-151, T&B CAT No.  RA753,
MIL-T-7928 MS-25036-152, T&B CAT No.  RB1323,
MIL-T-7928 MS-25036-153, T&B CAT No.  RB863,
MIL-T-7928 MS-25036-154, T&B CAT No.  RB713,
MIL-T-7928 MS-25036-155, T&B CAT No.  RB753,
MIL-T-7928 MS-25036-156, T&B CAT No.  RC863,
MIL-T-7928 MS-25036-157, T&B CAT No.  RC713,
MIL-T-7928 MS-25036-158, T&B CAT No.  RC753,

MIL-T-7928 MS-20659-101, T&B CAT No.  A85G,
MIL-T-7928 MS-20659-102, T&B CAT No.  A87G,
MIL-T-7928 MS-20659-103, T&B CAT No.  B85G,
MIL-T-7928 MS-20659-104, T&B CAT No.  B87G,
MIL-T-7928 MS-20659-105, T&B CAT No.  C26,
MIL-T-7928 MS-20659-106, T&B CAT No.  C70,
MIL-T-7928 MS-20659-107, T&B CAT No.  D10361,
MIL-T-7928 MS-20659-108, T&B CAT No.  D10721,
MIL-T-7928 MS-20659-109, T&B CAT No.  E10711,
MIL-T-7928 MS-20659-110, T&B CAT No.  E10731,
MIL-T-7928 MS-20659-111, T&B CAT No.  F10711,
MIL-T-7928 MS-20659-112, T&B CAT No.  F10731,
MIL-T-7928 MS-20659-113, T&B CAT No.  G971,
MIL-T-7928 MS-20659-114, T&B CAT No.  G973,
MIL-T-7928 MS-20659-115, T&B CAT No.  H971,
MIL-T-7928 MS-20659-116, T&B CAT No.  H973,
MIL-T-7928 MS-20659-117, T&B CAT No.  J971,
MIL-T-7928 MS-20659-118, T&B CAT No.  J973,
MIL-T-7928 MS-20659-119, T&B CAT No.  K972,
MIL-T-7928 MS-20659-120, T&B CAT No.  K973,
MIL-T-7928 MS-20659-121, T&B CAT No.  L973,
MIL-T-7928 MS-20659-122, T&B CAT No.  L975,
MIL-T-7928 MS-20659-123, T&B CAT No.  M973,
MIL-T-7928 MS-20659-124, T&B CAT No.  M975,
MIL-T-7928 MS-20659-128, T&B CAT No.  C73,
MIL-T-7928 MS-20659-129, T&B CAT No.  D10731,
MIL-T-7928 MS-20659-130, T&B CAT No.  E10261,
MIL-T-7928 MS-20659-131, T&B CAT No.  E10721,
MIL-T-7928 MS-20659-132, T&B CAT No.  F10721,
MIL-T-7928 MS-20659-133, T&B CAT No.  G975,
MIL-T-7928 MS-20659-134, T&B CAT No.  H975,
MIL-T-7928 MS-20659-135, T&B CAT No.  J975,
MIL-T-7928 MS-20659-136, T&B CAT No.  K975,
MIL-T-7928 MS-20659-140, T&B CAT No.  D10161,
MIL-T-7928 MS-20659-141, T&B CAT No.  D10711,
MIL-T-7928 MS-20659-144, T&B CAT No.  F10261,
MIL-T-7928 MS-20659-146, T&B CAT No.  G926,
MIL-T-7928 MS-20659-147, T&B CAT No.  G972,
MIL-T-7928 MS-20659-148, T&B CAT No.  G974,
MIL-T-7928 MS-20659-149, T&B CAT No.  H972,
MIL-T-7928 MS-20659-151, T&B CAT No.  J972,
MIL-T-7928 MS-20659-152, T&B CAT No.  J974,
MIL-T-7928 MS-20659-153, T&B CAT No.  K971,
MIL-T-7928 MS-20659-154, T&B CAT No.  K974,
MIL-T-7928 MS-20659-155, T&B CAT No.  L972,
MIL-T-7928 MS-20659-156, T&B CAT No.  L974,
MIL-T-7928 MS-20659-157, T&B CAT No.  M972,

MIL-T-7928 MS-20659-158, T&B CAT No.  M974,
MIL-T-7928 MS-20659-165, T&B CAT No.  C33,
MIL-T-7928 MS-20659-166, T&B CAT No. C75,

MIL-T-22909 MS-90485-8, T&B CAT No.  11781M,
MIL-T-22909 MS-90485-6, T&B CAT No.  11782M,
MIL-T-22909 MS-90485-4, T&B CAT No.  11783M,
MIL-T-22909 MS-90485-2, T&B CAT No.  11784M,
MIL-T-22909 MS-90485-1, T&B CAT No.  11785M,
MIL-T-22909 MS-90485-01, T&B CAT No.  11786M,
MIL-T-22909 MS-90485-02, T&B CAT No.  11787M,
MIL-T-22909 MS-90485-03, T&B CAT No.  11788M,
MIL-T-22909 MS-90485-04, T&B CAT No.  11789M,

MIL-T-7928 MS-17143-1, T&B CAT No.  RA480,
MIL-T-7928 MS-17143-2, T&B CAT No.  RB480,
MIL-T-7928 MS-17143-3, T&B CAT No.  RC480,
MIL-T-7928 MS-17143-4, T&B CAT No.  RA481,
MIL-T-7928 MS-17143-5, T&B CAT No.  RB481,
MIL-T-7928 MS-17143-6, T&B CAT No.  RC481,
MIL-T-7928 MS-17143-7, T&B CAT No.  RA482,
MIL-T-7928 MS-17143-8, T&B CAT No.  RB482,
MIL-T-7928 MS-17143-9, T&B CAT No.  RC482,
MIL-T-7928 MS-17143-10, T&B CAT No.  RA483,
MIL-T-7928 MS-17143-11, T&B CAT No.  RB483,
MIL-T-7928 MS-17143-12, T&B CAT No.  RC483,
MIL-T-7928 MS-17143-13, T&B CAT No.  RA484,
MIL-T-7928 MS-17143-14, T&B CAT No.  RB484,
MIL-T-7928 MS-17143-15, T&B CAT No.  RC484,
MIL-T-7928 MS-17143-16, T&B CAT No.  RA485,
MIL-T-7928 MS-17143-17, T&B CAT No.  RB485,
MIL-T-7928 MS-17143-19, T&B CAT No.  RA486,
MIL-T-7928 MS-17143-20, T&B CAT No.  RB486,

MIL-T-7928 MS-21004-1, T&B CAT No.  A486,
MIL-T-7928 MS-21004-2, T&B CAT No.  A483,
MIL-T-7928 MS-21004-3, T&B CAT No.  A482,
MIL-T-7928 MS-21004-4, T&B CAT No.  A481,
MIL-T-7928 MS-21004-5, T&B CAT No.  A485,
MIL-T-7928 MS-21004-6, T&B CAT No.  A484,
MIL-T-7928 MS-21004-7, T&B CAT No.  A480,
MIL-T-7928 MS-21004-8, T&B CAT No.  B486,
MIL-T-7928 MS-21004-9, T&B CAT No.  B483,
MIL-T-7928 MS-21004-10, T&B CAT No.  B482,
MIL-T-7928 MS-21004-11, T&B CAT No.  B481,
MIL-T-7928 MS-21004-12, T&B CAT No.  B485,
MIL-T-7928 MS-21004-13, T&B CAT No.  B484,
MIL-T-7928 MS-21004-14, T&B CAT No.  B480,
MIL-T-7928 MS-21004-15, T&B CAT No.  C486,
MIL-T-7928 MS-21004-16, T&B CAT No.  C483,
MIL-T-7928 MS-21004-17, T&B CAT No.  C482,
MIL-T-7928 MS-21004-18, T&B CAT No.  C481,
MIL-T-7928 MS-21004-19, T&B CAT No.  C485,
MIL-T-7928 MS-21004-20, T&B CAT No.  C484,
MIL-T-7928 MS-21004-21, T&B CAT No.  C480,

MIL-T-22909 MS-23002-8, T&B CAT No.  21707M,
MIL-T-22909 MS-23002-6, T&B CAT No.  21708M,
MIL-T-22909 MS-23002-4, T&B CAT No.  21709M,
MIL-T-22909 MS-23002-2, T&B CAT No.  21710M,
MIL-T-22909 MS-23002-1, T&B CAT No.  21711M,
MIL-T-22909 MS-23002-01, T&B CAT No.  21712M,
MIL-T-22909 MS-23002-02, T&B CAT No.  21713M,
MIL-T-22909 MS-23002-03, T&B CAT No.  21714M,
MIL-T-22909 MS-23002-04, T&B CAT No.  21715M

 

 

 

 

 

  

Technical Data

TnB StaKon Overview.pdf

TnB RA723.pdf

TnB StaKon Tool Chart.pdf

TnB StaKon WireGuide.pdf

TnB StaKon.pdf

 

 

 

 

 

  

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) NVNV-M162-10 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) NVNV-M162-10 사양에 대해 살펴보도록 하겠습니다.

 

 

 

Flexible Conduits & Fittings

T&B Catalog Number : NVNV-M162-10

UPC Number : 78620996388

Brand : PMA

 

 

 

 

 

Description

PMAFIX straight black connector with metric threads. Connector material - polyamide 6, thread material - nickel plated brass. Thread size - M16 x 1.5, thread length - 10, conduit size NW - 12.

 

Application

For use in the heavy machine and railway vehicle construction sectors where increased demands are made of the system properties

 

Characteristics

- Self-extinguishing, free from halogens and cadmium

- Excellent impact strength

- Extremely high thread and system connection strength

- Easy installation with the oval clip guarantees and excellent connection to PMAFLEX conduits

- Retaining clips offer high pull-out strength values.

- Fits both conduit profiles - Fine (T) and coarse (G)

 

  

 

 

  

Technical Data

TnB PMA Flexible Conduit Fittings.pdf

TnB PMA Technical Data Sheet.pdf

TnB pma chemical resistance chart.pdf

TnB pma reference guide.pdf

TnB pmafix orview.pdf

TnB pmafix connector Part number.pdf

 

 

 

 

  

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) D8-10 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) D8-10 사양에 대해 살펴보도록 하겠습니다.

 

 

 

 

Ring Terminal  

T&B Catalog Number : D8-10

UPC Number : 78621080353

 

Description

Non-Insulated - Brazed Seam Ring Terminal For Wire Range 8 Stud Size #10, Metallic

 

Features

These non-insulated ring terminals are made of electrolytic copper for high conductivity. They can be installed with crimping tools having a single indentor or double indentor (recommended for solid wire). Serrated barrel increases grip on wire.

  

 

 

 

Technical Data

TnB D8-10.pdf

TnB StaKon Overview.pdf

TnB StaKon WireGuide.pdf

 

 

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) Color-Keyed 256-30695-1302 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) Color-Keyed 256-30695-1302 사양에 대해 살펴보도록 하겠습니다.

 

 

  

Standard Barrel Copper Lug

T&B Catalog Number : 256-30695-1302

UPC Number : 78621017767

Color-Keyed

 

 

 

 

Description

Copper Two-Hole Lug - Straight Standard Barrel - max 35KV, #14-10 Wire, 3/8" Bolt Size, 1" Hole Spacing, Tin Plated with Inspection Hole,

  

 

  

 

General

Material : Copper

Finish : Tin Plated

Wire Size : #14-10

Number of Studs : 2

Stud Size : 3/8

Bolt Hole Spacing : 1

Tongue Angle : Straight

Barrel Length : Standard

Barrel Shape : Standard

Tongue Width : Standard

Peep Hole : Y

Marking : Standard

Hole Shape : Round

Die Color : Yellow

Die Code : ERG2002

 

Dimension Information

A (inches) : 2.369

B (inches) : 1.813

C (inches) : .563

D (inches) : .047

E (inches) : .266

F (inches) : .375

G (inches) : 1

 

Specifications

Voltage Rating : 600V to 35kV

  

 

 

 

 

 

Technical Data

TnB ColorKeyed 256306951302.pdf

TnB Colorkeyed App Book.pdf

TnB Connector Tooling Chart.pdf

 

 

 

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360A 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360A 사양에 대해 살펴보도록 하겠습니다.

 

 

Ball-Locking Type 

T&B Catalog Number : LS-7.9-360A

UPC Number : 78621024221

Ty-Rap

 

Description

Cable Tie 302/304 Stainless Steel 250lb 14" Ball Lock

  

 

 

 

 

 

General

Material : 304 Stainless Steel

Color : Metallic Gray

 

Dimension Information

Nominal Length (inches) : 14

Length (inches) : 14.2

Width (inches) : .310

Max. Wire Bundle Diameter (inches) : 4

 

Specifications

Temperature Rating : -112°F to 1000°F

 

Tooling

Application Tools : DAS-250

 

 

 

 

  

Technical Data

TnB TyRap LS79360A.pdf

TnB TyRap Overview.pdf

TnB TyRap Material Selection.pdf

 

 

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360B 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) Ty-Rap LS-7.9-360B 사양에 대해 살펴보도록 하겠습니다.

 

Ball-Locking Type

T&B Catalog Number : LS-7.9-360B

UPC Number : 78621024232

Ty-Rap

 

Description

Cable Tie 316 Stainless Steel 250lb 14" Ball Lock

  

 

 

 

 

General

Material : 316 Stainless Steel

Color : Metallic Gray

 

Dimension Information

Nominal Length (inches) : 14

Length (inches) : 14.2

Width (inches) : .310

Max. Wire Bundle Diameter (inches) : 4

 

Specifications

Temperature Rating : -112°F to 1000°F

 

Tooling

Application Tools : DAS-250

 

 

 

 

 

Technical Data

TnB TyRap LS79360B.pdf

TnB TyRap Overview.pdf

TnB TyRap Material Selection.pdf

 

 

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Thomas&Betts(T&B,TnB) Ty-Rap TYS5200H 사양소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 Thomas&Betts(T&B,TnB) Ty-Rap TYS5200H 사양에 대해 살펴보도록 하겠습니다.

 

 

Locking Heads

T&B Catalog Number : TYS5200H

UPC Number : 78621082697

Ty-Rap

 

 

Description

Cable Tie Stainless Steel Locking Heads

 

 

 

General

Material : 316 Stainless Steel

Color : Metallic Gray

 

Specifications

Temperature Rating : -112°F to 1000°F

 

 

 

Technical Data

TnB TyRap TYS5200H.pdf

TnB TyRap Overview.pdf

TnB TyRap Material Selection.pdf

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

파나소닉 Panasonic UV-Curing Systems, ANUP5256 Series 단종소식

 

안녕하세요  TIATIP 입니다.

 

오늘은 Panasonic UV -Curing Systems 가운데 ANUP5256 LAMP Area 경화기의 단종소식을 전합니다. 현재는 사용목적에 맞는 대체품이 없는 상황이지만, Spot 조사의 경우에는 ANUP50(UP50) 시리즈로 대안이 가능할 수 있겠습니다.

 

 

 

파나소닉 UV경화기/UV조사기

 

  

UV-Curing system Pana Cure Spot type ANUP5256 (Discontinued Products)

We are sorry, the products have been discontinued. Please refer to the details of the discontinued products and the recommended substitutes list below.

 

 

 

 Panasonic UV Curing Systems

 

(1) Discontinued Product

 

ANUP5256, Last Time Buy : August 31, 2010 To be discontinued

 

 

 

 

파나소닉 UV경화기/UV조사기

 

 

(2) Recommended substitute

 

Sorry, no suggested alternative products.
250W UV-Curing System (Direct Radiation Type). Lamp for exchange: ANUPS252, which manufacture will be continued. * : Instead of Direct Radiation Type, we offer 1.5kW Straight Lamp type UV Cuing Systems or the combination with 200W: ANUP50 and ø8mm Light guide: ANUP5081.
 

 

 

 

 

파나소닉 UV경화기/UV조사기

 

 

 

(3) Remark

 

ANUP50, Aicure UP50 LAMP Spot Type UV Curing Systems

 

  

 

 

 

Panasonic Nais IDK Aicure LAMP Spot UP50 EN 01.pdf

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

  

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

호크 Hawke S-Series Enclosure Size 9 기술사양

 

안녕하세요 TIATIP 입니다.

 

오늘은 호크 Hawke의 Stainless Steel JB/Enclosure로 대표되는 S-Series가운데, Size 9 Enclosure 사양을 살펴보겠습니다.

  

 

 

 

 

 

Hawke

Junction Boxes/Enclosures

S-Series Size 9 Enclosure

S-Series Stainless Steel

Increased Safety Exe / Dual Certified ATEX - IECEx  

 

 

  

Materials & Finishes

 

316 L Stainless Steel.

  

 

 

 

 

 

 

 

 

Technical Data

 

01. Increased Safety ex logo II 2 GD Exe II ExtD

02. Size 9 Certificate No's Baseefa08ATEX0208X and IECEx BAS 08.0065X.

03. Z Size 9 Certificate No's Baseefa08ATEX0207U and IECEx BAS 08.0064U.

04. Suitable for use in: Zone 1, Zone 2, Zone 21 and Zone 22.

05. Construction and Test Standards: IEC/EN 60079-0, IEC/EN 60079-7,

     IEC/EN 61241-0 and IEC/EN 61241-1.

06. Ingress Protection: IP66 to IEC/EN 60529.

07. Deluge Protection to: DTS01

08. Operating Temperature Range: -60°C to +80°C

09. Temperature class & ambient: T6 40°C, optional T5 with ambients up to 65°C.

   

 

 

 

Hawke

S-Series Size 9 Enclosure

S-Series Stainless Steel

Increased Safety Exe / Dual Certified ATEX - IECEx

S-Series Features

   

 

 

 

  

1.Softer Finished Rounded Edges

Safer manual handling of enclosure and gland plates.

 

2. Electropolished Surface Finish

Provides high levels of corrosion resistance.

 

 

 

 

 

  

3.Robust Stainless Steel Construction

Enclosure material thickness ranges between 1.2 – 2.0mm with 2 – 3mm thick gland plates. Durable stainless steel rating label.

 

4.Rigid Slotted External Mounting Feet

Allows enclosure to be hung onto the structure.

 

 

 

 

 

 5. Extensive Range of Enclosure Sizes Available

Eleven standard enclosure sizes available. Sizes range from 153 x 233 x 130 to 740 x 1000 x 210. Gland plates offered on two sides (Faces B & D) and bottom (Face C) of each enclosure. Alternatively, boxes are available with gland plates on Face C only.

 

 

 

 

 

 

 

6. Superior One Piece Silicone Sponge Gaskets

DTS01 deluge protection.
Provides Ingress Protection to IP66.
Durable with excellent UV stability and chemical resistance. – EMC mesh option.

 

 

 

 

 

 

7.Internal/External Earth Stud Fitted

 

8.Stainless Steel Lid Fixing Screws with Nylon Retaining Washers

Prevents loss of screws during assembly and maintenance. 

 

 

 

 

Hawke Full catalogues_20101103.zip

 

 

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

Hawke 호크 ICG653Universal P/ICG653UNIV P타입 기술사양

 

안녕하세요 TIATIP 입니다.

 

이번 시간에는 호크(Hawke) 케이블글랜드 가운데 컴파운드(Compound)의 타입이자, 콜드플로우특성(cold flow characteristics)을 겸비한 ICG653Universal Series(ICG653Univ Series)의 신제품인 P타입을 살펴보겠습니다. 기존 호크(Hawke)의 ICG653UNIVERSAL(ICG653UNIV)에 비해 IP(Ingress Protection)등급의 테스트 기준특성이 보다 강화되어 있다는 특징이 있습니다.

 

호크 케이블글랜드

Hawke ICG653/Universal/P, Hawke ICG653/Univ/P

Cable Glands

Hazardous Area

Flameproof Exd & Increased Safety Exe & Restricted

Dual Certified ATEX/IECEx

 

 

 

호크의 대표적인 Universal(UNIV) 시리즈인 ICG653 UNIVERSAL과 501453 UNIVERSAL 타입입니다. 각 5번항목에서 확인할 수 있듯이  ICG653UNIV는 레드라벨이 501453 UNIV는 블랙라벨이 장착되어 있어 외관상으로 식별이 용이하도록 구성되어있습니다.

 

호크 케이블글랜드와 커넥터가 Hawke의 정크션박스(GRP JB/Stainless JB)와의 연결구성이 가능하다는 이미지 예시

 

 

 

호크 HAWKE ICG653UNIV 시리즈의 Brass 재질 및 구성이미지

 

 

호크 HAWKE ICG653UNIV 시리즈의 Nickel Plated Brass 재질 및 구성이미지

 

 

호크 HAWKE ICG653UNIV 시리즈의 개별 패키지 이미지

 

 

 

Hawke Application

• Outdoor or indoor use.

• For use with single wire armour ‘W’, wire braid ‘X’, steel tape armour ‘Z’, elastomer and plastic insulated cables.

• For particular use with:
- Cables that are not eff ectively fi lled, compact and/or circular, have tape bedding or have hygroscopic fi llers.
- Cables that exhibit ‘Cold Flow’ characteristics.
- Enclosures containing an ignition source in gas group IIC areas or containing an ignition source in a Zone 1 area.

• See technical section for installation rules and regulations.

 

 

 

호크 Hawke 케이블글랜드 장착예시

 

 

Hawke Technical Data

• Flameproof Exd and Increased Safety Exe II 2 GD Extb IIIC.

• Certifi cate No’s: Baseefa06ATEX0058X and IECEx BAS 06.0015X.

• Suitable for use in Zone 1, Zone 2, Zone 21, Zone 22 and in Gas Groups IIA,

  IIB and IIC.

• Construction and Test Standards:

   IEC/EN 60079-0, IEC/EN 60079-1, IEC/EN 60079-7 and IEC/EN 60079-31.

 

 

호크 HAWKE ICG653UNIVERSAL Series

 

 

• Ingress Protection:

  IP66, IP67, IP 68 : 60 metres for 6 hours to IEC/EN 60529.

• Deluge Protection to DTS01.

• Operating Temperature Range: -60°C to +80°C.

• Assembly Instruction Sheet: AI 461 & AI 462 IP68 Sealing Method.

 

 

호크

HAWKE

 

 

Features

• Provides a barrier seal to the individual insulated cores within the cable and prevents entry of the products of an explosion into the cable.

• Assembly of the cable gland compresses and distributes the compound evenly to create a barrier seal at the point of entry into the enclosure.

• The compound chamber may be separated from the cured compound to ensure that the chamber has been eff ectively fi lled. If required, external voids can be repaired.

• Provides armour clamping, using one clamping arrangement for all armour / braid types.

• Provides an outer deluge seal to prevent moisture ingress to the cable armour / braid.

• Provides a cable retention and low smoke and fume, zero halogen seal onto the cables outer sheath.

• Manufactured in Brass (standard), Nickel Plated Brass, 316 Stainless Steel or Aluminium.

• Brass NPT entries are nickel plated as standard.

 

 

호크

HAWKE

 

 

HAWKE Ordering Information

ICG653/UNIV/P/Os/M20, ICG653/UNIVERSAL/P/Os/M20

ICG653/UNIV/P/O/M20, ICG653/UNIVERSAL/P/O/M20

ICG653/UNIV/P/A/M20, ICG653/UNIVERSAL/P/A/M20

ICG653/UNIV/P/B/M25, ICG653/UNIVERSAL/P/B/M25

ICG653/UNIV/P/C/M32, ICG653/UNIVERSAL/P/C/M32

ICG653/UNIV/P/C2/M40, ICG653/UNIVERSAL/P/C2/M40

ICG653/UNIV/P/D/M50, ICG653/UNIVERSAL/P/D/M50

ICG653/UNIV/P/E/M63, ICG653/UNIVERSAL/P/E/M63

ICG653/UNIV/P/F/M75, ICG653/UNIVERSAL/P/F/M75

ICG653/UNIV/P/Os/1/2"NPT, ICG653/UNIVERSAL/P/Os/1/2"NPT

ICG653/UNIV/P/O/1/2"NPT, ICG653/UNIVERSAL/P/O/1/2"NPT

ICG653/UNIV/P/A/3/4"NPT, ICG653/UNIVERSAL/P/A/3/4"NPT

ICG653/UNIV/P/A/1/2"NPT, ICG653/UNIVERSAL/P/A/1/2"NPT

ICG653/UNIV/P/B/1"NPT, ICG653/UNIVERSAL/P/B/1"NPT

ICG653/UNIV/P/B/3/4"NPT, ICG653/UNIVERSAL/P/B/3/4"NPT

ICG653/UNIV/P/C/1-1/4"NPT, ICG653/UNIVERSAL/P/C/1-1/4"NPT

ICG653/UNIV/P/C/1"NPT, ICG653/UNIVERSAL/P/C/1"NPT

ICG653/UNIV/P/C2/1-1/2"NPT, ICG653/UNIVERSAL/P/C2/1-1/2"NPT

ICG653/UNIV/P/C2/1-1/4"NPT, ICG653/UNIVERSAL/P/C2/1-1/4"NPT

ICG653/UNIV/P/D/1-1/2"NPT, ICG653/UNIVERSAL/P/D/1-1/2"NPT

ICG653/UNIV/P/D/2"NPT, ICG653/UNIVERSAL/P/D/2"NPT

ICG653/UNIV/P/E/2"NPT, ICG653/UNIVERSAL/P/E/2"NPT

ICG653/UNIV/P/E/2-1/2"NPT, ICG653/UNIVERSAL/P/E/2-1/2"NPT

ICG653/UNIV/P/F/2-1/2"NPT, ICG653/UNIVERSAL/P/F/2-1/2"NPT

ICG653/UNIV/P/F/3"NPT, ICG653/UNIVERSAL/P/F/3"NPT

 

 

 

 

 

Hawke Accessories 

 

 

 

 

호크 Hawke ICG653 Universal Series 설치동영상

 

 

 

 

ICG653 UNIV P Spec(UPD111213).pdf

ICG653 UNIV Spec.pdf

ICG653 UNIV P (Issue B 12-13) - RELEASED 11Dec13.pdf

ICG653 UNIV P Glands IP68 (Issue C 12-13) - RELEASED 11Dec13.pdf

2.Hawke Accessories 2013 IDK.pdf

 

  

 

 

 

 

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

T&B(TnB), Watertight, Flexible Connections Support Movement and Thermal Expansion 자료소개

 

안녕하세요 TIATIP 입니다.

 

T&B(TnB) Fittings 가운데 XD Expansion/Deflection Coupling for Rigid Conduit 자료를 살펴보겠습니다.

 

 

T&B (TNB, Thomas&Betts)

 

T&B® XD Expansion/Deflection Coupling for Rigid Conduit

A Better Solution for Expansion/Deflection Coupling of Rigid Metal Conduit!

 

Use the T&B XD Expansion/Deflection Coupling to join two conduit runs in applications where movement in any direction is required. The coupling provides a flexible, watertight connection, accommodating axial or parallel movement of up to 3⁄4" and angular movement of up to 30˚ from normal position.

While similar fittings exist on the market today, this new and enhanced XD Expansion/Deflection Coupling ships complete with an Erickson® type conduit union to significantly reduce installation time and effort and includes a stainless steel inner sleeve for extreme durability, protection and easier wire pulling. The hubs are zinc-plated and then coated with aluminum acrylic paint for dual-layer corrosion protection. In addition, the copper ground mounting plates and internal grounding bonding jumper are entirely enclosed inside the coupling for added security against vandalism and theft.

 

 

T&B(TnB), Typical Applications:
• Bridges
• Tunnels
• Inter-building walkways
• Docks and piers
• Wastewater and water treatment facilities
• Any other application in which conduit runs are subject to movement due to external forces or temperature changes

 

 

T&B(TnB), Features:
• Accommodates axial expansion/contraction up to 3⁄4", parallel deflection up to 3⁄4" and angular misalignment up to 30˚
• Suitable for use indoors, outdoors, direct buried or embedded in concrete
• Watertight, flexible neoprene outer jacket, zinc-plated and acrylic-painted hubs and stainless steel tamperproof straps ensure superior corrosion resistance — ideal for use in harsh environments
• Copper ground mounting plates and internal grounding bonding jumper both entirely enclosed to safeguard against theft
• Includes an Erickson® type conduit union for faster, easier installation to reduce labor costs
• Durable stainless steel inner sleeve provides a constant, smooth inner diameter in any position to ease wire pulling and protect wire insulation
from damage

• NPT threaded hubs fit standard threaded rigid metal conduit
• Can also be used with rigid PVC conduit with the use of standard adapters (not supplied)

 

 

T&B(TnB), Standard Materials/Finishes:
Hub: Ductile cast iron, zincplated and painted with aluminum acrylic paint
Inner Sleeve: Stainless steel
Internal Grounding Bonding Jumper: Flexible copper braid
Ground Mounting Plates: Copper Hub Rings: Zinc-plated steel
Outer Jacket: Molded neoprene (natural black)
Jacket Straps: Stainless steel

 

 

 

 

Why the T&B XD Expansion/Deflection Coupling is Better

1. Erickson® Type Conduit Union
Included union significantly speeds up installation, reducing your labor costs.


2.  Stainless Steel Inner Sleeve
Stronger and more durable than plastic tubes or corrugated hose and better able to withstand friction from pulling ropes. Provides a smooth transition to ease wire pulling and reduce chance of damage to wire insulation.


3. Enclosed Copper Ground Mounting Plates
Totally enclosed and secured with tamperproof stainless steel jacket straps for protection against vandalism and theft.


4. Dual-Layer Corrosion-Protected Hubs
Ductile cast iron hubs are zinc-plated and then coated with aluminum acrylic paint for extra corrosion resistance.

 

 

T&B(TnB), Catalogue Number & Keywords
T&B Fittings,XD Expansion Coupling,XD Deflection Coupling,XD3-TB,XD4-TB,XD5-TB,XD6-TB,XD7-TB,XD8-TB,XD9-TB,XD010-TB,
XD012-TB,XD014-TB,XD3TB,XD4TB,XD5TB,XD6TB,XD7TB,XD8TB,XD9TB, XD010TB,XD012TB,XD014TB

 

 

 

 

 

Rigid IMC Conduit Fittings.pdf

T&B Products Lineup Company Profile 2011EN IDK.pdf

 

 

  

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

티앤비(티엔비), Power Connection & Control 종합카탈로그 CAT03 소개

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 티앤비(티엔비) T&B(Thomas&Betts,TNB)의 Power Connection & Control 제품군에 대해 살펴보겠습니다. 총 19개의 Sector로 구성되어 있으므로 해당 브랜드별 자료를 참고하시기 바랍니다.

 

 

 

 

 

Connectors & Grounding


Blackburn® Compression Connectors Featuring the Color-Keyed® System

 

 

 

Compression Connectors for Copper Conductor
C-Tap Connectors for Copper Conductor
Copper H-Tap Connectors for Copper Conductor
Aluminum H-Tap Connectors

Interlocking Insulating Covers for Compression Taps
Wire Joints for Copper Conductor
Cast Copper Bus Taps for Copper Conductor
Motor Pigtail Connectors
KUBE® Connectors
Copper Disconnects
Connector Kits
Joint Compound
Connectors for Aluminum/Copper Code Conductor

Heavy-Duty Battery Connectors

Metric Connectors for Copper Conductor
Tools and Dies

 

 

Blackburn® Compression Connectors

 

 

 

 

 

 

Compression Connectors
Aluminum Lugs
Aluminum Splices

Tees

 


Blackburn® Mechanical Connectors

 

 

 

Split-Bolt Connectors
Service Post Connectors
Parallel Groove Connectors
Insulation Piercing Connectors
Two-Bolt Connectors
Insulated Multi-Taps
Power Distribution Blocks
Anti-Rotational Connectors
Dual-Rated Mechanical Connectors

Copper Mechanical Connectors
Clamp Connectors

 

 

Blackburn® Overhead Connectors

 

 

 

 

 

 

 

Storm-Safe® Service Entrance Disconnects
Service Entrance Splices
Aluminum H-Tap Connectors and Covers
Copper H-Tap Connectors
Stirrup Connectors
Hot-Line Clamps
Mechanical Service Entrance Connectors
Parallel-Groove Connectors
Full- and Semi-Tension Compression Splices
Compression Pin Terminals

Multi-Tap Eyebolt Connectors
Automatic Splices and Dead-Ends
Service Wedges
PowerTap™ Wedges
BolTap™ Wedges
PowerTap™ Tools and Accessories
Hydraulic PowerTap™ System

 


Blackburn® Grounding Systems

 

 

 

E-Z-Ground® Grounding Connectors
Cast Copper Connectors for Grounding
Ground Rod Clamps
Raised Floor System
Ground Rod Accessories
Ground Plates
Structure Grounding
Ground Clamps
Flexible Braid
Intersystem Bonding
Grounding Accessories
Exothermic Welding System

 

 

 


Homac® Underground Distribution

 

 

 

Aluminum Compression Splice Kits
Copper Compression Splice Kits
Mechanical Street Light Connectors
Breakaway Street Light Kits
Insulating Covers and End Caps
Pipe and Conduit Seals
Flood-Seal® Multi-Port Connectors
Pedestal Connectors and Covers
Stud-Mount Transformer Connectors
Pad-Mount Transformer Connectors

Network Protector Connectors
Drop-On Insulating Boots
Equipment Locks

Temporary Service Adapter System
Sealants and Lubricants
Wildlife Protectors

 

 


Homac® Substation Connectors
 

 

Weld Aluminum Connectors
Bolted Aluminum Connectors

Compression Aluminum Connectors
Bolted Bronze Connectors
EHV Connectors 

 

 

Wire Termination

 

Sta-Kon® Wire Termination & Insulation

 

 

 

 

Ring Terminals

Flag Terminals
Fork Terminals

Pin Terminals
Splice Connectors
Wire Joints
Heat-Shrinkable Terminals,
Splices, Disconnects
Disconnects and Male Tabs
Luminaire Disconnects
Ferrules
Wire Termination Tools and Installation Kits
Wire Termination Technical Information
Shrink-Kon® Heat-Shrinkable Tubing
Shrink-Kon® Splice Insulators and Insulating Covers
Shrink-Kon® Installation Tools
Shield-Kon® Shield Termination System
Dragon-Tooth® Magnet Wire
Termination System

 

 

Pos-E-Kon® Wire Pin & Sleeve Connectors

 

 

 

Series 16 Amps 600VAC
B Series 16 Amps 600VAC
C Series 35 Amps 600VAC
D Series 10 Amps 600VAC
DD Series 10 Amps 600VAC
K Series 80 + 16 Amps 600VAC
V Series 16 Amps 600VAC
T Series 16 Amps 600VAC

 

 

 

Power & High Voltage

 
Elastimold® Underground Cable Accessories

 

200-Amp Loadbreak Elbows
200-Amp Deadbreak Elbows
600-Amp Elbow Connectors
ComboT Integral Separable Connectors
600-Amp Separable Cable Joints
Multi-Point Junctions
Permanent Distribution Cable Joints
Distribution Shrink-Fit Terminations
Pre-Molded Terminations
Cable Shield Adapters and Jacket SealsEquipment Bushings
Medium-Voltage Cable Accessories Technical Information
Shielded Surge Arresters
Transmission Cable Joints
Transmission Cable Terminations
Transmission Cable Accessories Installation Tools
Transmission Cable Accessories Technical Information

 

 

 

Elastimold® & Hi-Tech® Fuse Products

 

Elastimold® Fused Loadbreak Elbows (FLE)
Elastimold® Molded Current-Limiting Fuses (MCLF)
Elastimold® Molded Canister Fuses (MCAN)
Hi-Tech® OS Series Back-Up Current-Limiting Fuses
Hi-Tech® EXT Series Back-Up Current-Limiting Fuses
Hi-Tech® FX Series Full-Range Current-Limiting Fuses
Hi-Tech® SX Series Full-Range Current-Limiting Fuses

Hi-Tech® EX Series Full-Range Current-Limiting Fuses

 

 


Elastimold® Molded Reclosers, Switches & Switchgear

 

 

Molded Vacuum Switches and Interrupters
Multi-Way Switchgear and Transfer Packages
Wind Turbine Power Protection
Molded Vacuum Reclosers

 


Joslyn Hi-Voltage® Capacitor Switches

 

VerSaVac® 15–38kV Capacitor Switches
Varmaster VBM 15–69kV Capacitor and Reactor Switches
VBU 69–230kV Capacitor Switches
Zero Voltage Closing Control Transmaster® VBT Electric Furnace Switches

 

 


Joslyn Hi-Voltage® Overhead Reclosers & Switches

 

 

TriMod™ Reclosers
Disconnect Switches
Load Interrupter Attachments

 


Fisher Pierce® Indicators, Sensors & Controls

 

 

Overhead Faulted Circuit Indicators
Underground Faulted Circuit Indicators
Cellular RTUs and Receivers
Clamp-Type Faulted Circuit Indicators
Test Point Indicators
Current Sensors

Capacitor Controls

 

 


Russellstoll® Pin & Sleeve Power Connectors

 

 

MaxGard® Interconnection Systems
J-Line™ Interconnection Systems
DuraGard® Waterproof Connections
FS/FD™ Metallic Connections
UniGard® Pin and Sleeve IEC Connections
DuraTite® and Ever-Lok® Locking Connections
Control Circuit Connections
Industrial Interlocked Receptacles
Hazardous Location Plugs, Receptacles and Interlocks
Safe Ground Indicator System
Computer System Interconnections
Mipco™ Connections for Refrigerated Containers 

 

 


Jennings® Vacuum Devices

 

High-Voltage Vacuum Fixed Capacitors
High-Voltage Vacuum Variable Capacitors
High-Voltage Vacuum and Gas-Filled Relays
High-Voltage Vacuum Coaxial Relays
Vacuum Contactors 

 


Cyberex® Mission Critical Power Quality

Digital Static Transfer Switches
Power Distribution Systems
Integrated Systems
Branch Circuit Management 

 

 

Cyberex® Industrial Power Conditioning

 

    

  

UL®/NEMA Industrial UPS Systems
IEC Industrial UPS Systems
Float Battery Chargers
Standalone Inverter Systems
Standalone Digital Static Transfer Switches

Power Distribution Systems

 

 

 

 

 

CAT03.01 Blackburn Compression Connectors Featuring the ColorKey

CAT03.02 Blackburn Compression Connectors.pdf

CAT03.03 Blackburn Mechanical Connectors.pdf

CAT03.04 Blackburn Overhead Connectors.pdf

CAT03.05 Blackburn Grounding Systems.pdf

CAT03.06 Homac Underground Distribution.pdf

CAT03.07 Homac Substation Connectors.pdf

CAT03.08 StaKon Wire Termination Insulation.pdf

CAT03.09 PosEKon Wire Pin Sleeve Connectors.pdf

CAT03.10 Elastimold Underground Cable Accessories.pdf

CAT03.11 Elastimold HiTech Fuse Products.pdf

CAT03.12 Elastimold Molded Reclosers Switches Switchgear.pdf

CAT03.13 Joslyn HiVoltage Capacitor Switches.pdf

CAT03.14 Joslyn HiVoltage Overhead Reclosers Switches.pdf

CAT03.15 Fisher Pierce Indicators Sensors Controls.pdf

CAT03.16 Russellstoll Pin Sleeve Power Connectors.pdf

CAT03.17 Jennings Vacuum Devices.pdf

CAT03.18 Cyberex Mission Critical Power Quality.pdf

CAT03.19 Cyberex Industrial Power Conditioning.pdf

T&B Products Lineup Company Profile 2011EN IDK.pdf

 

 

 

 

 

T&B, TNB, TaNdB

Thomas&Betts, ThomasaNdBetts

티앤비, 티엔비, 티앤드비, 티엔드비

토마스앤베츠, 토마스앤배츠, 토마스엔베츠, 토마스엔배츠

토머스앤베츠, 토머스앤배츠, 토머스엔베츠, 토머스엔배츠

  

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

티앤비(티엔비), Wire & Cable Management 종합카탈로그 CAT01 소개

 

안녕하세요 TIATIP 입니다.

 

오늘은 티앤비(티엔지) T&B(Thomas&Betts,TNB)의 제품군 가운데 Wire & Cable Management 분야에 관한 자료를 소개합니다. 총 16가지 Section 으로 구성되어 있으므로 해당 브랜드별 애플리케이션을 참고하시기 바랍니다.

 

 

 

 

 

 

Steel City® Metallic Boxes & Covers

 

 

Pre-Fab Components and Assemblies
Switch Boxes and Accessories
Round/Octagon Boxes and Accessories
Ceiling Fan Boxes and Accessories
Square Boxes and Accessories
Utility Boxes and Accessories
Handy Boxes and Accessories
Gang Boxes and Accessories
Concrete/Masonry Boxes and Accessories
Box Hangers and Supports
Stud Wall and Drywall Accessories

 

 

Carlon® Non-Metallic Boxes

 

 

 

Carlon® Blue™ PVC Boxes
Carlon® SuperBlue® Boxes
Polycarbonate Boxes

Phenolic Boxes
Non-Metallic Covers and Accessories
Low-Voltage Structured Cable Management System

 

 

 

Steel City® Floor Boxes

 

 

Recessed Service Floor Boxes
Flush Service Floor Boxes
Above-Floor Service Fittings
Replacement Parts and Accessories
Poke Through Systems
Access Floor Modules

 

 

Carlon® Floor Boxes

 

 

 

Residential Floor Boxes — Adjust-A-Box®
Residential Floor Boxes — Drop In
Rectangular Floor Boxes
Round Floor Boxes
Recessed Pop-Up Receptacle
Retractable Work Surface Receptacle

 

 

 

Red•Dot® Weatherproof Boxes and Covers


 

Weatherproof Metallic Covers
Weatherproof Non-Metallic Covers
Weatherproof Metallic Boxes
Weatherproof Non-Metallic Fixtures and Boxes
Weatherproof Metallic Lampholders
Weatherproof Non-Metallic Lampholders
Outdoor Lighting
Vaportight Lighting
Swimming Pool and Spa Products

Code Keeper® Universal While-In-Use Covers
Universal Flip-Lid Weatherproof Covers
Code Keeper® Universal Recessed Box and Cover

 

 

 

Carlon® Enclosures & Junction Boxes

 

 

 

 

 

 

 

Carlon® Non-Metallic Junction Boxes

Circuit Safe® NEMA Enclosures
Circuit Safe® JIC Enclosures

Circuit Safe® Pushbutton Enclosures

Circuit Safe® Enclosure Accessories

Himeline® Enclosures

Slack and Splice Enclosures

 

 

Carlon® Electrical Non-Metallic Tubing (ENT) System

 

Electrical Non-Metallic Tubing
Boxes and Accessories

Flexible Raceway Systems
Flexible Raceway System Accessories

 

 

 

Kindorf® Modular Metal Framing System


 

 

Channels, Nuts and Fittings
Conduit, Cable and Pipe Supports
Concrete Inserts
Beam Clamps and Hanger Rod Supports
Wall and Support Brackets
Surface Raceway and Lighting Support Systems
Hardware and Threaded Components
Cable and Mounting Systems
Right Angle Slotted Angle Systems
Non-Metallic Channel and Accessories

Trap-Eze™ Connector

Trapnut® Strut Fastener
Fast Set Beam Clamp
Loc-King™ Cobra® Cable and Pipe Clamp
Solar-Panel Hold-Down Clamps and Washer

 

 

Superstrut® Metal Framing System


 

 

Channels

Threaded Products and Hardware

Fittings and Brackets
Concrete Inserts
Beam Clamps
Pipe Straps, Conduit Clamps and Hangers

Surface Raceway and Lighting Systems

Slotted Angle Metal Framing
Special Metals and Finishes.

 

 

 

Steel City® Hangers, Clamps & Fasteners


 

 

Beam and Purlin Clamps
Hangers

Conduit and Cable Supports
Stud Wall/Drywall Supports, Clips and Brackets
Acoustical Tee Supports, Clips and Brackets
Low-Voltage/Datacom Hooks, Hangers and Brackets
Fastener Accessories and Hardware

 

 

T&B® Cable Tray


 

 

Cable Tray Closure End Plate

 

 

 

Cable Ties, Tools & Accessories

 

 

 

 

 

 

 

 

Ty-Rap® High-Performance Nylon Cable Ties
Engineered-Performance Material Cable Ties
Color Coding Cable Ties
Identification Tags, Cable Ties and Accessories
Mounting Bases, Cable Ties and Accessories
Safety, Reusable and Double-Loop Cable Ties
Messenger and Lashing Ties and Straps
Deltec® Cable Tie and Support System
Ty-Rap® High-Performance Stainless Steel Cable Ties
Hook-and-Loop Fasteners
Ty-Rap® Installation Tools
Ty-Rap® Wire Management Clips, Clamps,
Spiral Wrap and More

 

 

Catamount® General-Purpose


 

 

 

 

Ties & Accessories
Twist Tail® Cable Ties
General-Purpose Cable Ties and Accessories

 

 

 

Wiring Duct & Wiring Trough

 

 

Ty-Duct® Wiring Duct
Wiring Duct Tools and Accessories
Wiring Duct Technical Information
Carlon® Wiring Trough and Accessories
Wiring Trough Technical Information

 

 

EZCODE® Identification Products


 

 

 

 

 

 

 

 

 

 

Wire and Cable Marking
Tags
Labels
Signs
Warning Tapes

 

 

 

Catamount® Electrician’s Supplies

 

 

 

Wire Connectors
Wire Pulling Lubricants
Electrician Hand Tools
Hardware and Rough-In Products
Wire Testing Equipment

 

 

 

 

CAT01.01 Steel City Metallic Boxes Covers.pdf

CAT01.02 Carlon NonMetallic Boxes.pdf

CAT01.03 Steel City Floor Boxes.pdf

CAT01.04 Carlon Floor Boxes.pdf

CAT01.05 RedDot Weatherproof Boxes Covers.pdf

CAT01.06 Carlon Enclosures Junction Boxes.pdf

CAT01.07 Carlon Electrical NonMetallicTubing ENT System.pdf

CAT01.08 Kindorf Modular Metal Framing System.pdf

CAT01.09 Superstrut Metal Framing System.pdf

CAT01.10 Steel City Hangers Clamps Fasteners.pdf

CAT01.11 T&B Cable Tray.pdf

CAT01.12 TyRap HighPerformance Cable Ties Tools Accessories.pdf

CAT01.13 Catamount GeneralPurposeTies Accessories.pdf

CAT01.14 Wiring Duct Wiring T.pdf

CAT01.15 EZCODE Identification Products.pdf

CAT01.16 Catamount Electricians Supplies.pdf

T&B Products Lineup Company Profile 2011EN IDK.pdf

 

 

 

 

T&B, TNB, TaNdB

Thomas&Betts, ThomasaNdBetts

티앤비, 티엔비, 티앤드비, 티엔드비

토마스앤베츠, 토마스앤배츠, 토마스엔베츠, 토마스엔배츠

토머스앤베츠, 토머스앤배츠, 토머스엔베츠, 토머스엔배츠

  

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

티앤비(티엔비), T&B Fittings, Shureflex Nylon Liquidtight Conduit System 자료

 

안녕하세요 TIATIP 입니다.

 

오늘 이 시간에는 티앤비(티엔비) T&B(Thomas&Betts,TNB)의 Fitting류 가운데 Shureflex 제품을 살펴보겠습니다.

 

Fast and Flexible Protection for Electrical Cables
Shureflex™
Nylon Liquidtight Conduit System

 

 

Quick and Secure One Piece Fitting Installation With No Tools Required!

The new line of Shureflex™ Nylon Liquidtight Conduit and Fittings
from Thomas & Betts provides all of the benefits of a halogen-free,
watertight system for protection of electrical cables-plus hasslefree
installation to save you time and money.


With its unique, self-locking mechanism, the Shureflex™ system enables quick and secure installation without tools. Simply push the fitting onto the conduit, and you’ve achieved an IP66-rated seal with superior mechanical strength. For a higher IP rating, use the same fitting; just add a sealing washer to the fitting
and an O-ring to the conduit. Now you’ve achieved IP68 and IP69K
protection. Disconnecting is just as easy-press the release ring on
the fitting and twist and pull out the conduit. No tools are needed, and you
can reuse both conduit and fittings.


The T&B® Shureflex™ Nylon Liquidtight
Conduit System includes three grades of conduit to meet varying flexibility
and crush-resistance needs. Choose among straight and 90˚ fittings with
NPT and ISO threads, T fittings, Y distributors and a variety of other available fittings for special applications-plus a full range of accessories like sealing washers, O-rings, locknuts and mounting brackets-to meet all of your needs for safe, secure and watertight connections.

 

◎ Flexible, lightweight Polyamide 6 or 12 (PA6 or PA12) construction
◎ Halogen-, phosphor- and cadmiumfree material-ideal for use in confined spaces
◎ UL94V-2 or UL94HB flammability rating for safety
◎ Achieve IP66, IP68 and IP69K watertight ratings with just one fitting
◎ Wide operating temperature range of -40˚ C to 105˚ C or -50˚ C to 90˚ C
◎ Complete system includes three grades of conduit, a variety of fittings
and accessories

◎ UL Recognized

 

Applications:
◎ Wind turbines
◎ Passenger rail
◎ Shipbuilding
◎ Robotics
◎ Aviation
◎ Automotive
◎ Machine Builders
◎ Tunnels
◎ Telecom
◎ Confined Spaces
◎ Use Indoors or Outdoors

 

 

 

 

 

 

 

Shureflex Nylon Liquidtight Conduit System.pdf

T&B Products Lineup Company Profile 2011EN IDK.pdf

 

 

 

 

 

T&B, TNB, TaNdB

Thomas&Betts, ThomasaNdBetts

티앤비, 티엔비, 티앤드비, 티엔드비

토마스앤베츠, 토마스앤배츠, 토마스엔베츠, 토마스엔배츠

토머스앤베츠, 토머스앤배츠, 토머스엔베츠, 토머스엔배츠

  

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절

티앤비(티엔비), Harnessflex Protection for Critical Electrical & Electronic    Cable CAT 2011 소개

 

안녕하세요 TIATIP 입니다.

 

티앤비(티엔비) T&B(Thomas&Betts,TNB) 제품군 가운데 특수 목적의 컨듀이트(Conduit) 분야 전문브랜드인 Harnessflex 를 알아보겠습니다.

 

 

 

 

 

 

Conduit
NC
CTPA
HNC
CPC
PP/DSPP
PKC
HTC

 

 


 

Hinged fittings

Joiners
Elbows
Tee Pieces
Y Pieces
Shrouds
X Pieces
Manifolds
Split Manifolds 

Circular Manifolds

Interfaces
Amp Superseal
Amp Junior
Ampseal
Deutsch DT
Deutsch DT04
Deutsch DRC50
FCI
Bosch compact
Delphi Series
Kostal
Milflex ABS
DIN 72585
Circular Connectors
Other Interfaces
Accessories 45Amp CPC


 

Sealed Fittings
Straights

Elbows
90o degree flanges
Tee's
X Pieces

Manifolds
Circular UNEF
Solenoid Connectors
Reducers
Glands
Accessories
Clips

 

 

 

 

      

Harnessflex 2011 CAT 0.00.pdf

CAT02.07 Harnessflex Specialty Conduit Systems.pdf

CAT22 Harnessflex.pdf

T&B Products Lineup Company Profile 2011EN IDK.pdf

 

 

 

 

T&B, TNB, TaNdB

Thomas&Betts, ThomasaNdBetts

티앤비, 티엔비, 티앤드비, 티엔드비

토마스앤베츠, 토마스앤배츠, 토마스엔베츠, 토마스엔배츠

토머스앤베츠, 토머스앤배츠, 토머스엔베츠, 토머스엔배츠

  

 

 

 

 

  

내 기술지원 및 구매상담처

CUSTOMER SUCCESS IDK

deric@jadongwha.com

www.tiatip.com

 

 

저작자 표시
신고
Posted by TIATIP

댓글을 달아주세요:: 네티켓은 기본, 스팸은 사절


BLOG main image
by TIATIP

카테고리

TI Story (957)
TIA (92)
TIP (194)
TIEx (601)
TIS (36)
TIO (23)
TiNoTe (10)
The OtherS (1)